A variety of construction materials provides plenty of options for decoration - it is logical!Facing plastic panels, with its simplicity and low price, good option in terms of aesthetics.
He - one of the simplest device, fast and practical.
eliminate all the flaws of the ceiling foundation can without much preparation work surface.The ceiling mounted panels are most suitable for areas where frequent temperature changes and high humidity: bathrooms, showers, bathrooms, terraces, balconies and loggias.
can Morkovkina Zagovezni to look at photos of finished ceiling, but did not understand their design.And you can read the recommendations of the short, quick to understand them - and detailed instructions will no longer need, you will be able to design finishes.
panels - versatile material!They can be fixed up and down, diagonally, you can come up with patterns and ornaments, and realize all this alone, without an invitation expensive specialists.How?We tell the essence.
ceiling installation PVC panels can be made on a wooden frame , either on a frame made of metal sheets - galvanized steel or aluminum (see: How do self-install PVC panels to the ceiling).For dry rooms suitable wooden block, and for bathrooms and other damp rooms is better to use the profile of the metal.
Important!The main point: choose the direction of the panels, lath and Design across their length.Along the edges of the location of the mandatory and step should be no more than 50-60 cm, to false ceilings made of plastic panels do not sag under its own weight.
- space that is formed between the panels and the ceiling, if necessary, can be filled with insulation (sm.Uteplitel ceiling - make the right choice), soundproofing and heat insulation.You can arrange a vapor barrier, it is important for rooms with high humidity.
After selecting the type of crates should immediately decide on the lights.If
provides built-in lights, you must lower the ceiling, taking into account the size of lighting fixtures.
depth of fixtures 5 to 10 centimeters.After receiving the level of the ceiling of the future, it is necessary to project it to the walls around the perimeter.
Important!At fixing hanging lamps must necessarily hold lath and attach lighting it, and not to the panels.
- How to measure the distance, as the projected location of the main guiding profiles?You can measure it from the banal base, but in this case horizontally completely guaranteed.
much more correct to use the water level (or laser), but in the absence can be applied to a normal level of the building, only to take longer, even meter.
The process proceeds as follows
Focusing on the resulting line on the perimeter of the walls attached profile 25x25 mm (if wood), using dowel-nail, if the walls are concrete orbrick. in private homes to the wooden walls can be fixed even nails , anywhere design is not going anywhere.
In the corners profile connects with screws or prosekatelem.
seams perpendicular to the direction of panels drawn line with the above steps, indicating the place of installation support section.Profiles are cut so that they entered into its long established crates.
To this end, pieces of wood are cut notches, while all metal sheets is a much simpler.
As drafted lines are attached to the ceiling in increments of 1 meter direct hangers that are hung profiles batten.At the junction profiles batten them interconnected to increase the hardness.
to the guide profile along the walls with screws screwed start with the profile indicated by step. Pre-start profile in the corners cut at 45 degrees.
After installing the battens, if necessary, it is important not to forget the complete wiring for lighting equipment.The same applies to the other low-voltage systems, air ducts, cables and other things that will take place on the ceiling.
being installed across the profiles - all intuitive.How to mount plastic panels to profile and each other - there are instructions from the manufacturer (sm.Montazh plastic panels on the ceiling with his hands).
sliced panel as one assembly.Cutting possible hacksaw, grinder or jigsaw, followed by mopping up sandpaper or abrasive mesh.
option with a space between the panels
in the starting end profile of the plant, slightly curved panel and start up a second.Further, the panel slides into the side profile.
After installing the panels in the correct position, it is fixed to the profiles with self-tapping screws pressshayboy.Similarly, all subsequent panels are mounted.
last panel width is cut out of the actual razmeru.Potolok hinged panels ready for installation of lamps!
Just on our website you can learn about how to make the PVC ceiling panels with their own hands.