Skirting performs not only a decorative function, it can protect the joints and panels from cracking.Therefore, it is not unimportant question of fixing.
better glue ceiling moldings we cover in this article.It will be given step by step instructions to perform the work.You can see the videos and photos in the internet and decide on the form elements.
Choose ceiling moldings
most frequently used baseboards or polyurethane foam.
These materials are similar in structure and are polymeric:
- Foam skirting tighter, but is lighter in weight.It has a lower purchase price.Less elastic.Crumble while cutting.But it is good to cut and easier;
- Polyurethane , more robust design.It is better to bend, unlike the first embodiment.Different strength and elasticity.Price above from the previous foam member.
well tolerated high humidity and is suitable for installation in the bathroom and kitchen.It has a glossy surface and a porous
determine the amount of material simply
should never take the material in the butt.Calculate how much is part of integral elements and calculate how much will go to waste and add to this the 15% and it will be the right amount.
must now determine the width of the material.In retail, there are many types and configurations of elements.The width depends on the height of the ceiling.
At high ceilings, you can take a wider elements.When the standard height of the best fit elements with a width of 45 mm.
Note: Keep in mind, if you take much stucco relief, have to constantly go up and dusting.The greater the relief, the greater the accumulation of dust.
most commonly used in the repair of the apartment are two methods of fixing the plinth:
- In the first version, the plinth is secured by a conventional sealant or glue on top of the wallpaper;
- In the second embodiment, first moldings glued on top of the prepared surface and only after this is done pasting wallpaper.
The second method is more time consuming, but it is much more practical.This is reflected in the fact that at least the next repair will not have to remove the baseboards, and it will be necessary only likely to remove old wallpaper.
And secondly, when uneven walls are very evident cracks and unevenness between the wall and the skirting.Which is easier to do before gluing wallpaper.
installing baseboard to securing wallpaper you'll avoid contamination during the conduct of operations. and elements will look like a single unit with the plane of the ceiling.The better to stick skirting ceiling, will be discussed below.
Thinking better glue ceiling moldings, clearly we can say it is better to perform the repair.Then there will be the opportunity to do it properly and efficiently.
It's not a difficult job, and it can be done by hand.First you buy the items in the right quantities, the price of the material is not so high and you can choose exactly what is right for you.
now about what to glue skirting ceiling.
- If you had decided to paint the ceiling surface, then the elements must be attached directly to the plaster.After the material to dry out and close up any gaps between the ceiling and stucco elements.Thereafter, the surface color should be performed;
- If you decide to make the design of the ceiling in the implementation of which is provided for mounting rails or other elements, then you must first do the job, and only then begin to install the floor.
Tools and materials
to carry out work, we need the following tools:
- Clay, which is made of polymer-based;
- putty, based on PVA;
- knife assembly;
- ruler or measuring tape;
- Abrasive paper;
- Sealant, preference is given to colorless.
After all the work to create the desired design of the plane, the surface should be treated with topcoat, which you can read the details on our website.
And after a full treatment can proceed directly to the installation:
- Fastening elements should be carried out according to the layout you want to do right.To do this, take one item and attach it to the ceiling at the level that you need, and draw a line on the wall.
Warning: Partitioning is a very serious matter and which should be taken very seriously.The surface can be smooth enough, and you can not see with the eyes.However, fixing it is quite noticeable and can lead to a distortion of fastening elements.
- perform a mark should be transferred to the other wall. To qualitatively do better to use the hydraulic level.Then should mark all interconnected.To do this, use a nylon thread.With its help line just bounces;
- Details plinth should be fixed by using glue or putty, which is made of water-based.If you are using powerful items, then reliability should be used screws.
To install should make a hole in the wall with the gun.To do so, make a hole in the first part plinth using a drill.
Further, the element should be attached to the surface and through the hole to make a mark on the solid surface.Next, remove the plinth and make a hole.After this fixation can be performed.
Note: The baseboard should make a hole on one mm larger than the wall.If this is not done tears can perform on a plane.There will be a bite material.Always on the baseboard should be chamfered, it will obnizheniem for screw and allow the hat to hide.
- installation design should begin to perform from the corner of the room. should take the element and apply it to the previously beaten off and spend the second, only the surface of the ceiling;
- After this shift element for connecting wall and also draw a straight line on the ceiling, which intersects with the first;
- To properly cut the angle, it is necessary to note the point of intersection of the baseboard lines.This point will be cut with respect to the reference plane;
- When it first does the same with another element.As a result, we get the angle of attachment;
- adhered evenly applied layer of the mixture and add it to the plane. The pressure should be made from the beginning of the other mating part and evenly move in the opposite direction ;
that after a plinth trim, always have to attach the material to the plane of the dry dock and check the quality.If a connection with screws, then should first make a dock and then to carry out the mounting holes.
- for direct connections, perform better on both trim elements that the end was at an angle of 90 *, then the connection quality will be better.For this to work better to use miter box;
- After connecting joints should be treated with putty.We should immediately cover up and place fastening screws .;
- After a while the adhesive hardens, and the foundation have to walk at the seams with sandpaper or mesh construction;
- Now you can make and paint the surface.Some people prefer to apply gold leaf to the surface.This is done using a brush and thin bronze.It is possible to apply the paint and the other, it all depends on your desire.
Now it must be said, than to stick to the ceiling moldings ceilings (see: How do stick to the ceiling moldings stretch ceilings yourself) installation of special distinction in this matter.
Just have some features of material selection:
- Preference should be given to lighter materials because mount will hold only a portion of which is connected to the wall;
- When you select should pay attention to the material with the wider part of the abutment wall;
- When buying material, fixtures, consult your dealer and read the instructions, it must approach the film coatings and solvents manufactured without additives.
carefully reading the article, you can easily do the job.