The wooden house ceilings installed more easily than in a brick.Not least because that attachment is not required to apply the hammer and drill holes in the brick.
However, there are some nuances, such as lighting fixtures harder to hold.Wood is a combustible material and therefore require reliable isolation.
about this and it will go to our article.
Choose ceiling material
Before you get started, it is necessary to determine the material to set.We have two options.
stretch ceiling with film
As the name implies, the basis of the design is a film which is made of PVC.Tension ceilings in a wooden house with PVC film easily stretched during heating.
This work is carried out using a heat gun and fasteners is a baguette, which is mounted on the circuit element.
In this embodiment, there are advantages and disadvantages:
- When setting we obtain perfectly flat and smooth surface;
- not a high price of the material;
- large number of colors and in retail sales.
has its drawbacks.
- film is a soft material that easily can be damaged;
- Bonding is a seam which is visible;
- unpleasant smell during the installation design;
- His hands will not install because you need special equipment for installation;
- biggest drawback is not resistant to temperature extremes.
stretch ceiling cloth
At the heart of this design is the fabric.
that are more durable material in contrast to the first option:
- Such material is much wider than the film and reaches 5 meters in width;
- has higher strength;
- resistant to temperature;
- Easy to install and maintain.
has its drawbacks:
- fabric can only be matte;
- not stretched;
- pass water;
- When connecting seam is visible, as is done only through the separator.
Installation tissue stretch ceiling
The wooden house suspended ceiling is fixed in the same way as in any other.Just make the connection process is carried out with screws, which greatly facilitates installation.
In this article we will talk about the installation of tissue structure.Videos and photos you will find in the internet themselves, define the color and pattern.
you will be given step by step instructions for carrying out the work.
Tools and materials
All work must begin with the drawing and the purchase of tools and materials.Design solution you have chosen, you must now make the necessary purchases.
need the following tools:
- Water level.If you have, then the suit and a laser;
- screwdriver and hacksaw;
- Nylon thread;
- sharp knife;
- pencil, screwdriver and pliers;
should purchase the following materials:
- beam, with a cross section of not less than 25 mm ;
- Fabric suspended ceiling;
- Baguette (profile);
Warning: For installation, choose a material timber with a moisture content of 8-10 percent.After that it should be treated with a protective liquid, which will prevent the formation of rot.
It is in retailing.
Stretch ceiling in a wooden house should begin to establish a definition of the height of the structure. For this note the pipes and communication that you want to hide.
this altitude you must be a bar to set the framework.
Note: If only the wooden house built, then should not rush to a false ceiling installation.You should wait about 5 years , while the design will not give a complete shrinkage.Otherwise
with subsidence may occur and not fold the canvas.Take your time in this matter.
- Put a mark on the wall where the line will be the installation of the ceiling.Then this point now taking on another wall.
For this purpose the hydraulic level which will give the most accurate results;
- Then take a nylon thread and fend line around the perimeter of the installation.We got a loop fastener design;
- Make pruning bars along the length of the walls and fasten them on the perimeter of the room.
Warning: Do not make the exact size of the timber.When fixing element must not touch the wall, you should make a gap of about one centimeter.
this we will avoid warping the expansion of the web in the case of high humidity or temperature .. This gap will be closed in the finishing skirting.
- weight fabric ceiling is higher than that of the film structure.Therefore, the point of attachment should be placed every 15 cm-Th;
- We stretch the line diagonally across the room.This will be the level of the rest of the mounting bar.
carefully adjusting the plane of mounting, it has to be perfect.To adjust it, apply the pads;
- Then do the rest of the mounting bar.Step installation use no more than 60 cm;
Once we have a robust and durable design frame, the wiring should be done milking lighting.This is done prior to installation of the coating.So
- find points of connection.It is better to install a junction box to perform wiring.This is required by the rules and fire safety;
Note: When laying the cable, it is best placed in a fireproof sleeve.Avoid twists when making connections.
better to use the terminal blocks, which will provide reliable protection and prevent circuit in the connection point.Do not forget that a tree is a flammable material.
- Make cable wiring to the installation of lighting fixtures.Fasten the wire to the ceiling;
- At points where lamps do release the cable to be enough to connect the fixture.
Now is the time to do the stretch fabric.For this purpose two methods can be applied.
- makes installation PVC moldings around the perimeter of the room.To him will be attached sheet.Perform mounting with screws;
Note: When making a connection to do obnizhenie screw.When then will be able to finish this point and putty to hide itself hat;
- make the primary cross.Expand canvas.Take
hand corners, which is located on the widest part of the mount and dressed them for prints. long end of the input should be around 20 cm. work is carried out with a spatula;
- Take a sheet from the opposite edge, and just tucked into a baguette from this side.
Attention: do not overdo it stretch, fabric should be taut, but not to go out for a baguette, which is located on the opposite side.
- Then do the stretch ceiling fabric and the rest of the canvas;
- Now that the initial installation is done, and the acquired form of the cross, begin to fill the canvas along the perimeter of the room.Starting from the middle of the broad side.
with a spatula dressed with canvas prints, and move to the corner of the room;
- do the job accurately, "roll up" the canvas with a spatula for a baguette .Next, go to the opposite side of the unit and do the same;
- during refueling can not drag the fabric.Do everything neat and wrinkle-free.
- In the final stage of installation must fill corners and trim the excess fabric.To install a ceiling was perfect canvas is sometimes necessary to trim with scissors and then carefully fill in the baseboard;By
- fabric edge remains, which should be cut with a knife around the perimeter of the mounting unit.
making holes in the stretch ceilings
During installation, you will need to do the web holes in the fabric base.They should be carried out correctly (see: How do make a hole in the ceiling of the tension with his hands).So
- Cut the ring that will not allow the web to spread after installation.You can use the material that is in the retail trade.
But sometimes the hole and not the standard type.Then edging have to do it yourself.
This will require a soft plastic with a thickness of 1-2 mm. on its surface mark a cut line using a marker.
along the contour cut with scissors;
Caution: Never do the exact size of the hole.Especially for heating pipes.Make allowance upwards.Material should not be heated in the heat supply.
- Using a knife is a hole in the material of the ceiling;
- on the surface of the plastic glue is applied;We put
- edging to the web and the fastening surface.
hole done.If you are not white canvas.
Then cut off part of it.Apply glue and then dressed with the material under the plastic edging.
Hide the seams
Well, if the fabric is enough for the whole plane setup, but sometimes you have to sew it.And then there is a question about hiding seams.So
- To start cook the paste to which should be added to the PVA glue in a ratio of 1: 3;
- mixed well and bring to a state of the liquid cream with water;
- apply it to the surface of the tracing paper and glued to the ceiling;
Attention: Tracing paper is cut into strips and glued lap, after the connection surfaces on them have to walk Zero sandpaper.
- After drying interface will not be visible.
This design appeared relatively recently, but it is popular.In this case, the ceiling surface, using wooden beams, is divided into cells, which is set in the middle of the canvas.
Note: To make better use of cells softwood lumber.Which dried out and treated with antiseptics.
a resinous wood structure not susceptible to change Antiseptic humidity to prevent mold and rot
- Choose a timber according to the room.It should take into account the weight of the structure.We can not allow slack elements;
- Further, all as previously described.Note the lower point and drag it to the other wall;
- Make the skip level fastener;
- Make the skip cell lines installation;
- first timber fastened along the length of the room;
- then do insert elements smaller.For the correctness of the attachment is better to make a template from plywood.Before
broken regularly distributed dimensions of the elements.Everything must be done in alignment;
- should not forget about the installation of lighting fixtures that can be attached not only to the ceiling, but also a tree.However, this should be done before the installation of the web.
wooden construction houses, is in itself quite sturdy and warm structure.However, it is subject to decay.
properly handle all of the surfaces and the design will please you for many years.