Many people want to make a unique ceiling finish.But I do not know exactly how to perform the pieces of drywall on the ceiling.
The internet has a lot of video and photos on this topic.However, it should be step by step instructions in this matter, and you will find below.
The more you can do with your hands, and avoid these additional expenses.The price of the material is not as high and the more it does not need much more to repair the ceiling.
The deal may go and waste that remained at the time of repair.
Thin sheets arched
When buying material, you probably noticed that the sale is arched and drywall, which has a thin thickness and better processed, its thickness is only 6.5 mm .
Bend design is not as hard in the middle of a sheet of reinforced using fiberglass, this makes the material more ductile.To set the start frame (sm.Karkas ceiling plasterboard - all the little things or little things do not happen.).
- first applied to the ceiling drawing what we want to see;
- Then take a profile and do desperately to stiffeners, and then fasten it to the surface;
- cut from a sheet of drywall material the desired size;
Warning: Do not do drywall butt.Consider how the line will overlap joint material.
Only then can cut out completely.
cutting material is not such a difficult question:
- To do this, look for a straight, flat surface.It is best to approach the table.
- celebrate the cut line, and with a pencil and ruler draw the line.
- displaces it relative to the plane of five mm.
- puts on a direct rail line section and spend the material knife.That should be sharp.
- Then abruptly break the sheet.It turns out the ideal cutting line.
If the edge has turned out not even eliminates this by plane.Do not forget to remove the chamfer, which is required in the putty surface (sm.Shpaklevka ceiling with his hands, the choice of material, advice).
- After harvesting to the figures ready, begin to fix it to the profile by means of screws.We do it gently, without much effort.
should be said that in this way, we can only figure with a large radius.Not great design makes a little differently.
Arch drywall, it is not durable material.If you want to rigidity figure is performed in two layers.
methods bend drywall
dry method Drywall bending
the dry drywall bending radius depends on the material thickness and slightly affected by humidity.
This parameter is displayed in the table:
|thickness drywall||mm minimum bend radius mm|
- for such an option is best to take the material with a width not exceeding 60 see .;
- Bending is performed only in the length of material and in the direction of fiber;
- Fixing should be done with a distance of at least 15 see .;
not forget about accuracy.Do not bend too sharply.
need a soft and uniform pressure.
wet method of bending
In the wet process can reduce the performance of the bending radius of itself, but it also depends on the thickness of the material and its moisture content.
|thickness drywall||mm minimum bend radius mm|
If the bend radius you want a wet process, then it is as follows:
- makes the template for fixing material.You can not apply the necessary pieces of drywall.If you can set the material directly on the mounting location, then the template can not do;
- carving out the right size with a sheet of drywall, if the item is large, you can use the waste;
- laminating one side using a needle roller and put it on pre-cooked bars.This will avoid soaking the front of the material.
Note: Prevent water from entering the front of the material in the water soaking.Otherwise, there will be gaps on the surface and to fix it is sometimes very difficult, and sometimes impossible.
- moisten the sponge in the water and begin watering punctured side of the workpiece.To do so as long as no more water to soak into the surface;
- Set on the prepared sheet workpiece centering it and bend.Do this carefully and accurately;
Note: In the manufacture of the template should take into account that it should be a little less than the required size.It should be taken into account the material thickness.
- fix a set piece.This can be done using adhesive tape or a clamp;
- bending is only possible along the length of the material, as in the previous dry process;
- allowed to perform installation directly on the profile, but in this case, you should reduce the distance between the profiles.In this embodiment, the bend should not twist the screw until it stops, it should be done after the complete drying of the material;
Bend drywall using cuts
This method is perfect for long-range performance is not possible to manufacture and 10 cm .Only to perform such work will need to purchase a special tool.It
required for the grooves on the back side of the sheet, which is U-shaped form.In carrying out this work can not damage the face of the workpiece.
After making the grooves sheet can be given the desired shape and then to process the filler.Wait until completely dry and ready form.
perform such work should be in the following order:
- Remember bending shape will depend entirely on the gap between the cut.Pers a larger number of grooves, the radius can be made smaller;
- Make the required number of cuts, and laid on the prepared blank template.Completely clean the surface from dust and debris;
- Take the putty to dry mixture and add to water and thus interfere.
is best suited for this drill with paddle, it will provide good mixing and eliminate the formation of lumps.Bring to a density of sour cream;
- With spatula apply the mixture to the surface and fill all the voids;
- We wait complete drying and fixed on the desired surface.
Note: If you need to perform a large radius, then it can be done with a few elements.Only then must be attached on the surface of the galvanized band radius.
It will give the necessary rigidity.
Doing star plasterboard
plasterboard can be almost any shape.We have described the most complex option is to perform radius.
elements from an acute angle prosche.Mozhno do much to make, and the star.
- do on the surface of the drawing.When, and we should not forget about the thickness of the material.With his star will mount a little more;
- cut the profile to size and mount it on the plane.Interconnections are made using self-tapping screws;
- Cut the sheets of drywall to length;
Warning: The edges of the cut pieces should be treated with a plane and make the right joint elements.The angle is performed according to the drawing.
- Fasten the workpiece to the profile.Please try on all of the elements and look at the dock.
Only then do the final fixture;
- Put the material on the stars and made the contour Contour cutting with a pencil;
- crop unwanted parts and are attached to the surface.
- Shpaklyuem compound (sm.Shpaklevka ceiling (choice) - doing the right thing).
After drying is performed on the surface finishing time, which you can read in detail on our website.