ceiling trim balconies, garage, baths, built in the yard, and with the onset of cold weather there is accumulation of water droplets on the surface and the gradual deterioration of the material.Sound familiar?
condensate on the surface of the ceiling is the worst enemy of premises of buildings with poor insulation measures were taken to the roof or the ceiling inside.How to fight it?
need to understand and address the root cause, identify activities and pick up the necessary materials to conduct a competent work and enjoy the result.What we present you with detailed advice.
This paper guide will talk about how to get rid of the moisture on the ceiling.Getting.
most common - a high absolute humidity in the room .A little behind the bad air-conditioning, for those spaces where you can not perform constant air extraction.
high humidity typical for space in the basement, cellar or individual buildings such as a garage, is not insulated and poorly ventilated.This
Why does condensation?On the one hand overlap cools frosty air.
Once unheated, not warmed the room cools, condensate wait.Warm air from the inside reaches the cold surface of the material or the finishing of floors, and rapidly cooled.
That is the notorious dew point, it is not "cold bridges", which is so afraid of everything.Technically not going to decipher.
What do you need?We need to isolate the material with his own hands from the cold finishing material overlap.
Moreover, if, for example, the ceiling in the garage of the main iron!High-quality insulation "will remove the" high heat transfer between the materials.Finishing
not be cooled by the cold air will not condense.
opportunity to spend a lot of insulation!
- insulated with mineral wool;
- expanded clay;
- Brick fight any other fragmental material fines, between them there is enough air pockets;
- Foam insulation, which are applied mechanized.And so on, in fact.
method of warming already choose their own, the technology - for the selected materials.
There are several steps that have to be followed.Since the condensate is already there, it is not necessary to have warned.
It must be eliminated.But only a one-time removal of the result will not bring the moisture will appear again if the cause is not eliminated.
It will be necessary to divert the water to prepare some materials:
- Polyethylene film, try to trim your own area, depending on the size of the room;
- galvanized iron for the production of "umbrella".Construct a better look at the photo, and manufacturing technology - video on the Internet, because visually it is easier to imagine than to describe;
- Plastic pipes, sewer can be.
Surely you to hang the ceiling with his hands, so should know about its design.And you know what it horizontal.
You will need to break this thing, "tilting" the ceiling, giving the surface of the slope, not necessarily strong.This is necessary so that the water as droplets therein flowed to the edge.
Under this edge, which is designed slope of the ceiling, you need to make a likeness of the drain, bring it out and send in a specially installed capacity. And on top of this drainage to protect umbrella.
This brief.But it is desirable, although many completely ignore this step.
now try to give a full list of activities, with details:
- humidity being checked and evaluated the quality of ventilation and air conditioning system performance.For normal ventilation in the room needed to circulate the air in the amount of total space -3 hour.
to modern balcony with plastic window systems and outside, and inside, to reach such volumes is possible only with proper ventilation, even constant ventilation will not help.
- checked layer of insulation, if any is present. If there is visible damage or insulation impregnated with moisture and does not dry chronically, it must be removed and replaced.
In any case, if there is condensation in the room, then ono- cold and heat insulation should be carried out again.
- desirable when selecting a heater to look at its technical characteristics (smUteplitel ceiling - make the right choice).
Not all insulation materials are designed to absorb excess moisture, but there are others, which absorbs well and then easily give .That is, dry up quickly.
- the ceiling above, if possible, you need to pour a concrete block or brick fight, not only large fragments.Do not dust, because in brick dust will not air spaces that we need to keep warm.
ceiling balcony pour it does not work, but at a garage or other building - please.
- For greater fidelity in a cold room, and it is desirable to consider measures for wall insulation.
Tip!If we are dealing with a garage or similar structure, which is not heated, but is heated periodically - perhaps completely get rid of the condensation on the ceiling, you do not get.
Then you need to do for the removal of the condensate, which is described above.Just dig another special pit where the water will be taken away and the soil.
internal insulation space
Tip!Just pay attention to the degree of surface dampness may moisture affected the base, penetrating deep into the floor.To eliminate this phenomenon will have to carry out uninteresting drying facilities using heat gun.
Depending on the specifications of the equipment and the degree of dampening material process can take from one day to a week!See additional technology.
What do we do next?We select the required number of extruded polystyrene, which is briefly called Epps.
and thickness of the sheets is also adjusted depending on the degree of freezing, it will write to you any instruction to complete insulation.Sheets cut so as to completely cover the entire surface of the substrate and sticking them on the floor.
In this case the price of the material is fully justified, so the price does not look, choose quality.
seams putty, repaired the walls of the compound, it will eliminate the infiltration of cold air under a layer of insulation .And would not change the Epps on the foam!
In general, the internal insulation of the room, in this case - the construction or imposed separately from the general warm apartment balcony - it's not a good thing.It is much more efficient to carry out external insulation, but it is not always possible.
Only for balconies
for balconies (see: How do insulate the ceiling on the balcony - to create comfort with his hands) have to choose a certain type of materials that have very low water vapor permeability.Just extruded polystyrene is very suitable!
At normal temperatures somewhere in the south of the country, you can restrict the thickness of boards no more than 30 mm , and for the middle band is optimal to choose 50-60 mm .
boards extruded polystyrene
When installing panels on the glue still secure their anchors as possible soaking adhesive.Before mounting surface swipe reinforcing fiberglass mesh.