child's room should not just be finished - there need to design, able to create the mood of the child.Plasterboard for the child is the most important element of the decor of the room, it is only with the help of the FCL can be set up so bizarre forms and shapes stacked.
In this article you will be given a small guide on "How to make plasterboard with their hands in the nursery," as well as are a few examples of his finishing.
makes the figure on the ceiling
to a room intended for accommodation of the child, it presented much more requirements than any other room.So
- One of these conditions, can be considered the use in the decoration of only natural materials, which may include drywall. And when you consider that it can be used to perform the configuration of any complexity, it is the GCR and the need to adopt, performing design of the space.
- Despite the fact that the ceiling in the children of plasterboard takes at least twelve centimeters height of the room, for a child it is not very important.In the children's room, as well as in the bedroom of an adult, low ceilings are welcome.
room, where a man sleeps with the ceiling becomes more comfortable and cozy.
- choosing what figure decorate the ceiling of plasterboard in the nursery, it is necessary to take into account the child's gender, age, interests.It can be considered a win-win option patterned ceiling "clouds".
Thus, it may well be the simplest: in one level.
What you need to work
This configuration of the ceiling, as in the photo above, is not difficult to perform, but there are two levels.Just one level smoothly into the other.
ceiling plane is somewhat biased, made with a bias in one direction, closing the bend joint walls and ceilings.
- As you can see on the above example, a bend is made of ceiling profile by performing on it incision.This is done by conventional metal shears.
to perform a variety of shapes and curved configurations can be purchased and a special arched profile.
- By building ceilings in plasterboard child, you need a certain set of tools.Drill, hammer, screwdriver and hammer with screwdrivers, there almost every host.
Anyway, everyone knows that these tools are.With them will be set a framework for the ceiling plasterboard.
- to work with sheets GCR need a special cutter;edging roughing and planes;a circular saw, a saw or a knife;Needle roller.In addition, we have already listed, need prosekatel, building level, square, ink thread, narrow and wide spatulas, fine sandpaper.
- for cutting plasterboard in a straight line, you can use not only the cutter, and special knife for cutting drywall.It looks like a normal office knife, but it has reinforced blade.
To get a quality cut is necessary to control the force applied when pressing the knife.
- cutter blade or knife to make an incision should only cardboard envelope and go deep into the interior of the gypsum core only a couple of millimeters.After the incision is made, the sheet refract and incision carton shell on the other side.
- for cutting curves used jigsaw.Only in this case, the sheet must be cut through, instead of refracted.
- ceilings Children plasterboard may require the fulfillment of not only flat shapes, but the bulk.And then to bend the sheet in the desired radius, you need a template.
- ceiling design of each individual, so the template in the store can not buy.It needs to be made independently, using the materials at hand.The price of such products is minimized.
Naturally, the size of the template should be carefully calculated.To understand all the intricacies of the process, look its best.
- for adaptive drywall, use two methods.Wet technique involves bending the sheet in humid condition.
compresses the wet side of the sheet is perforated with a spiked roller, they encircle the template so that the center part coincides with its axis.
- After drying, the shape of the workpiece is saved.The thicker the sheet, the more difficult it is bent, and the bending radius increases.
Although, if you want to create a small bend radius, it is best to use a dry method of bending.
- By the way, there is a kind of galactic cosmic rays, whose core is reinforced with fiberglass.If you use it, performing for children's ceiling of plasterboard, the template you may not need.
- reinforced GCR more durable and thin, just 6.5 mm, and very good bends dry method.If this thickness is insufficient to carry out the design, lists a geminate.
- If bent drywall dry method, the workpiece is not perforated, and the convex side of a router make cuts and cuts.The curved blank is first coated with primer and then shpaklyuyut and grind.
mounted on a frame ready, prepared for finishing, details.
- framework will need to install two types of profile.One of them, trim (PP), is mounted on the perimeter walls.
On the other, the guide profile (PPN) will be using direct hangers fixed drywall.
If the length of suspension is not enough, use a pin extender that can lower the ceiling, at least one meter.And, of course, we need fasteners: dowels, screws and two types - one for the profile, the other for the drywall.
Once cleared of the old ceiling coverings, moldings and fixtures removed, proceed to markup.So
- Looking at the lowest point of the ceiling, which will be zero. With the level now taking this point on the wall, and lay it on the distance by which the surface of the suspension will deviate from the base of the ceiling.
- Around the perimeter walls of the horizontal line is drawn - it will be mounted on the trim profile.If the ceiling has a two-level or three-dimensional shape of the contours should be also applied to the ceiling with a pencil.
- Sometimes plasterboard ceilings Children are very interesting.For example: the figure and captures part of the wall, in this case, the marking should be applied on it.
- When markup is finished, you can start mounting Wall Profile PP60 * 27.If you would like to buy imported profile, it can not be called PP, and UD.And size may vary slightly.
- install plasterboard in the nursery, and in any other room, alone uncomfortable, so be careful with that, to have an assistant.It will keep the profile, and you - to work puncher.
And you need to install the sheets together, especially when they have a large format 1.2 * 2.5 m.
- before mounting frame applied trim profile to the horizontal line marking, and right through him punch drill dowel holes, which then clog.
- If the ceiling of one level smoothly into the other, as is the example where the ceiling depicts the "cloud", the markings on this side will have two lines.Accordingly, the installation of PP profile will be at the lower mark.
then these levels will need to connect an arched profile, which we discussed above.
- Next steps 60cm, a ceiling mounted guiding profile DPU 28 * 27 (CD) .He must rely on the trim profile.A fix to the base ceiling, as you can see on the chart, is made on direct suspensions.
- By the way, the distance between the lath belts still sixty centimeters no accident.Most ceiling modules and panels have either the same size or width of a multiple of this number.
sheets GCR also has a width of 60cm, and there are 1.2 m, so be assembled on a crate is very user-friendly.
- If a large area of the room, and the length of the profile is not enough, do not worry.Just slice the missing piece with the expectation that it will not rested butt in the already mounted profile, and there is a gap of one to two millimeters.
- order on curves, make a smooth bend profile, the two sides will have to cut its shelves, and remove their segments.The profile is mounted laterally from step 40-50cm, depending on the curvature of the surround member.
At the intersections of the profiles set duplex connectors.
- finished assembling the frame of the first level, you can start the implementation of the framework of the second level, what, in fact, is the figure on the ceiling.Its installation can be carried out to the slab, and to have the first level steering plasterboard ceiling.
It depends on the complexity of the figures, stresses that it will produce to other parts of the ceiling or wall.There is no single recipe, we must act on the situation.
If you are new in this business, do not hold directly behind the complex configuration.Try to start to deal with a simple structure, as in the example above.
Designs and finishing
As we have said, plasterboard ceilings in the nursery are selected and drawn up taking into account the child's age.The youngest children, it is interesting to see the sun on the ceiling, clouds, colorful butterflies and ladybugs.A good choice is
- After plastered all shapes and mounted on the ceiling, it is the turn of finishing.But first you need to be repaired all the joints of pieces from the ceiling, the seams between the sheets, rising above on the surface of the GCR head screws.
- After processing ground, made Shpatlevanie, then sanding and intermediate coat.Such training will be enough, in those places where the surface is papered drywall adhesive foil, or embossed wallpaper.
- Those areas that will be painted, it is necessary to putty completely.In our example, with a rainbow on the ceiling, use both finishing.Fragments
rainbow colored, and "bottomless sky" turned pasting first through the ceiling of glossy blue film.
- If the room is large enough, the sky with clouds floating by, and can be obtained with the help of photo wallpapers.Pay attention to how the spotlights are located - on segments of the rainbow.
In the evening, with the lights on the ceiling is a beautiful picture.
- Speaking of lamps.Creating a plasterboard ceiling in the children, all the electrical work, installation of related lighting, additional switches, equipment for lighting, made immediately after the installation process framework.
- Here, for example, a room high schooler.Of course, no butterflies here should not be, especially if the occupant of the room - a boy.
This ceiling, as our example, perform even easier.
- There have curved shapes, only one level, and not on the entire area of the ceiling, and only the perimeter, in the form of a wide cornice.It mounted and spotlights and neon lights made zakarniznaya cord.
- color gypsum cornice is in harmony with the image of the metropolis on the Mural.It's simple and tasteful - take note!
- The girl's room, the ceiling can be done, for example, such a figure, as in the picture above.Its area is small, so you can manually paint the figure.
It is much easier to make than the paste over all facets of film.In this example, to decorate the ends of the fragments of striped wallpaper, and the horizontal portion of a colored tone.
- figure on the ceiling is not "live" in itself.She has to be in harmony with the interior.
In this case, it blends perfectly with the coloring wallpaper, and of course curtains.
choosing a design for a child's room, talk with your child.It's no wonder they say that the child's mouth speaketh the truth.
Let him feel the importance of the event and responsible for their choices.He will never tell you, "But I do not like ...»