Not so long ago we could ceiling just whitewash or paint.Now the market has been selling a variety of materials to do the job.In this article, we will tell you about a relatively new form of equipment-ceiling mirrored ceilings are plastic.
In an Internet can view photos and video of this material and find the right design.There will be provided instructions for installation of the material.
Plastic mirrored ceiling
This material is relatively recently came to our market.The panels are made according to special technology and price is a little higher than normal material.However, this design has many advantages.
- perhaps most important, it is that such a ceiling would allow visually raise the plane and increase the area of the premises;
- Easy to install.This construct can be assembled with their hands, and without recourse to outside assistance (sm.Samostoyatelny ceiling mounting rack).Rather it will be able to provide and relatives.It boils down to the fact that it will be necessary to maintain the elements at their attachment;
- waterproof material allows it to be installed in areas with high humidity;
- In such a structure can be applied to almost any lighting;
- material sufficiently resistant to fading for a long time and retains its original properties;
- With this construction, increased sound insulation of the room.It is possible to install and extra insulation;
- This environmentally friendly material , which is not harmful to human health;
- calmly withstand elevated temperatures.It does not burn or melt;
- easy to clean.Treatment is not allowed obrazivnymi detergents;
For continuous operation should buy the necessary material.
- Such panels may be of different lengths and widths.Therefore, should first Gaugeable room and calculate the amount of plastic mirror panels;
Attention: podschete first determine the direction of the elements.The calculations consider and waste.Fold first whole number of elements, and only then Calculate the amount of missing material.
- After that it is necessary to draw a map of the installation cover.To do this, draw a footprint, and parallels are drawn.This will be the profile that should be fixed at a distance of 60cm.This will help to calculate the number of profiles that will be required for mounting;
Note: Along the perimeter of the room is fixed UD profile, it is more rigid.Cross-fixing is done using a profile CD, it is more lightweight design.
- Fixing approximately calculated as follows: count the number and profile of his works on 50 cm. So we get a number of anchors that are required to complete the fixture;
- moldings: Take the perimeter of the room and divide by three.We get the number of plinths;
Note: To add to the results to be 10%.This material goes to waste.It should be also taken into account.
To design was for a long time and looked good, it is necessary to carefully choose the panel (sm.Zerkalnye panel on the ceiling - highlight in interior design).
They can be identified by the following principles:
- manufacturer that makes quality products and guarantees, always cover the glossy protective film parts.This will protect the material during transportation;
- Quality panel when pressed lightly defomiruetsya, but will not crack;
- Before buying, take one item and gently bend it in the same place about five times, the panel should return to its original position and is not deformed, the gloss is not damaged;
This work is carried out in several stages:
- Surface preparation;
- mount crates;
- layout of lighting fixtures;
- mount panels;
- Installing the plinth.
now turn to the Installation and describe it in detail and gradually.
Preparation and installation of a skeleton
start production of construction with preparation of the base surface for attaching the ceiling.This is a very important stage.On this plane panel will be installed, and on its quality will depend on the design and appearance.
- To install mirrored plastic ceiling, should first determine their level installation.We were in the room very low angle.We add to it the height of the profile.We add the thickness of the panel and put a mark;
Note: If you plan to install additional insulation, then select the profile that the sheets of insulation placed freely and do not press the panel.Otherwise, the insulation loses its properties.He must be free to lie down and cuddle.
- We have a mark for attaching the ceiling.Now it should be moved to the other wall.This is done using hydraulic level, it will allow more qualitatively the dimension.We transfer the risks and put a mark;
- Now we need to connect the set point.To do this, we use nylon thread.With its help repel level ceiling installation;
- According done marking is done by setting the profile on the perimeter of the room.This will punch through which a hole is made in a solid surface.If the wall is made of wood, then you can mount with screws;
- then makes the connection of the transverse profile.To do this, we use the same punch.These will be attached and mirror panels;
Warning: When the holes do not damage the wiring.Before the beginning of the attachment should see the plan of conducting cable.If not, you should ping the ceiling for any wiring.
All wiring for lighting devices after installing the frame:
- First, find a point of connection of wires and install a junction box;
- Then mark up the seat mounting fixtures;
- Making channels for wires and connect it;
- Fasten the wire to the base plane of the ceiling;
- Locations O lighting elements do release the wire to the desired length.Do not do the rest of the wires in the butt, perform tolerance upwards;
- Connect lighting.We connect power supply and look at the correctness of the installation of lighting fixtures and light distribution.
Avoid wiring connections stranding use the terminal blocks.They provide a reliable connection.
Everything must be done accurately.Remember, if damaged wiring is not so easy to fix the damage.
will need to remove cells.Do not perform the work while it is energized.
After setting the framework and validation of lighting, you can install the mirror panels.When performing the installation, you can not remove the protective film from the mirror surface, it is better to do it after the attachment.
Note: If you plan to install additional insulation, then it should be done after mounting frame and wiring installation.When making connections, do not damage the wiring.
- installation begins at the corner of the room and fixing is performed to set the profile with screws;
- Each successive panel is mounted in the grooves, and the previous cell is connected to the frame;
- at fixing fixtures should be installed elements.This will require making a hole with a knife or a special cup;
Note: Prior to installation, determine the design.It is not always include the entire elements.Usually they require pruning.Take note of this.
- last panel of the installation is cut to length.This is done using a hacksaw with a fine tooth.If you use a large tooth, the material will have a snack and damage the glossy surface;
- Now, after fixing the panels should be installed ceiling moldings.This gives details on our website.I should say one thing, pick the correct width of the element.It serves also as a design, but also covers the junction member and the coated wall.
plastic mirror on the ceiling is installed correctly.Now you can remove the protective film, and look at their work, which will serve you for years to come.