Make a hole in the stretch ceilings, this issue occurs when you install the structure.And if you know how to do this, then it is not so difficult.
main thing to make this work.There are different kinds of holes, so we'll show you how to perform them correctly.
Video and photo on this topic in the internet there.Step by step instructions will be given below.
hole bypass pipe
bypass pipe is required to perform when installing almost any stretch ceiling.(See. Installation of suspended ceilings) There are several ways to do this work, they all depend on the specific situation.
There are several factors that affect the performance of such tasks:
- distance from the pipe wall;
- color of the cloth;
- slope of the pipe.
His hands can do all the work.And the issue price is not so high, it is the main focus.So
- first step is to cut the ring that will prevent the spread of the web and at the same time give an acceptable edge of the hole elastic appearance;
- For its production used plastic, which has a thickness of mm 1-2 .Further, a rectangular hole cut out, which must be greater than the pipe diameter 0.5-1 cm distance from the edge of the web should be chosen too such;
- We measure the diameter of the pipe and then to make the plastic circle diameter should be greater than the diameter of the pipe to be 6 mm.
- Then otcherchivaem outer part of the ring, the edge should be in the form of a semicircle.Through the center line of the wire radius, which should be located close to the edge;
- cropped The lead product.That we get ready to ring.Now we begin to work with the material;
This is a fairly simple way, when you need to make a ring around the edge of the canvas.
For this type of work can be applied two options:
- himself plastic, usually is white, and this method is used for seamless PVC ceiling white.Initially fueled film around the room installation.
But do not reach the pipe, about 20 cm-be on both sides.Then, perform the cut fabric in the center of the pipe and fasten the canvas for the prints.
Then poddevat ring through the tube and glue it to the plane;
Note: If the coating itself does not have any white in this case should be cut a little fabric and close the ring with this material, and fill the inside edge.
In this method, the ring adheres more evenly.Even if the pipe is removed from the wall or is tilted, this embodiment is difficult to err.
There are times when it is necessary to set the ring inside the ceiling.
This method is precisely suited to this option:
- Prev dressing canvas prints, you should warm up the side of the film, where the pipe;
- We stretch the heated side of the tube in the direction of the hands, apply to this harpoon.Note the location of the center of the pipe;
- The place puts a gluing something smooth and hard, and be sure to apply the adhesive.We combine odds with the mark on the shaft.Glue the ring and at the same time let go of the spear;
- pressed tightly against the ring, and in this way we maintain the order of 10 sec .;
- With a sharp knife cut out through the ring canvas (with the spear).After that cut the hole for the pipe in the form of a cross;
- We have a triangle that should bend inward and glue;
- The web is adhered to the ring is worn on the pipe.Cut the plastic "lock" and is attached to the back side of the ring.Harpoon while glued to a piece of cloth;
- Making stretch ceiling is made from the nearest corner to the pipe.This embodiment is only applied to openings PVC film.
Note: If you are close to two pipes, in this case, you should do one ring on both pipes.
When installing a suspended ceiling all faced with the question of manufacturing the hole for the light.(See. How to make lamps) Today we'll show you how to do this during the installation phase and is ready to fulfill even at the ceiling.Although
before installation design it is better to determine the locations of lighting fixtures.In this case, the work is much easier to simply perform.
When installing ceiling
It should be said at once, mounting fixtures performed on mortgages, to which is fastened to a lamp.When this is done in the web opening.
And if you do it on the right, it just gets going, what will become worthless entire structure:
- all the work should begin with the implementation of the markings on the plane.Just do it right, and keep in mind when calculating the power of lighting (sm.Lyustry for ceilings: the selection and application);
- First you need to install yourself mortgages which are fixed according to the markings made.Mortgages are in retail, where they can be purchased.
If, by virtue of any reason you can not do that, they can be made and most.
Cut rings of plastic, the thickness of which must be of the order of 5-10 mm .Fix them to the ceiling with hangers.
diameter rings do so, as in the fixture.For proper implementation of this work should be bought in advance all the lights.
- Further, according to the curve of the suspension, adjusting all the rings.They should all be located under the plane of the ceiling, which will later be installed;
- Next to all the lighting equipment should fail wiring;
Note: At this stage, you should check the work lighting.While it is possible to change their position.Extend or reduce the wire.
- makes the installation of the web.After that hand feel for the place of installation of fixtures and make a mark at these points using a marker;
- Cut rings of thin plastic, the size of the fixture.This problem can and simplify buying ready-made ring in the store.
They have not a high price, and reduce the time required for manufacturing;
- greased surface of the ring with glue and glued them on previously marked places;
- cut a hole in the ring;
Note: When cutting, use a sharp knife only.If this condition is not only spoil the plane surface.And it is quite difficult to fix.
- In the opening scene we take out the wire and install the lamp.
the openings to the finished ceiling
If you need to make a hole in the ceiling is already finished, it can be done with their own hands and without the need for outside help.
Warning: should pay attention to one detail, if the warranty on the installation of the ceiling has not expired and you'll be doing it yourself, may lose the guarantee on the product.In this case, you should consult with the company, which has established.
If you are engaged in installing the ceiling, then the question is no longer relevant, and can be started.
Note: Any opening in the film and performed at a plastic ring.Which can be purchased at retail, or do it yourself.Otherwise, the film may break, and the product will be ruined.
It is used when you decide to install additional lamp or chandelier:
- Remove the fabric from the ceiling and set in place the mortgages securing fixtures .Then again, it is necessary to pull the film;
- for places to install lighting glue plastic rings.First, adhesive is applied to the ring plane, and then putting a and pressed on the surface of the film;
- After drying glued to the ring to cut a hole with a sharp knife.There will be placed lighting apparatus;
- chandelier installation is performed in a different way, if it is placed on the hook.In this embodiment, it is not necessary to remove the film.
In this case, just the beginning to the installation ring is attached.After drying, a hole was drilled.
Then fasten the hook to the base of the ceiling using dowels.Pre-drilled using the perforator.
This option is ideal if you need to make a hole in the ceiling of the gravity to drain the water.
If a neighbor so do a service to you, then if there is lighting, additional holes do not have to.So
- first step is to disconnect the wiring and drain the water through the holes in the hose can help.If there are no holes, just release the film at an angle of baguette and drain the water.
After this operation the film is stretched itself and takes its original appearance.
Note: If you are flooded with water over 65-year-degrees, will have to change the canvas completely.The film at that temperature comes into disrepair.
Sometimes it is necessary to make a pass to the joints or other communications wiring.
If you often have to climb beyond the plane of the ceiling, in this case, a window should be made for this work:
- Buy plastic with a thickness of 3-5 mm. and cut out of it a frame, with the value that you need.It may be of various sizes and shapes;
- Apply glue on the frame and glue it to the location of the window;
- We wait complete drying of the film and cut inside the frame with a sharp knife.
Note: When making this hole, attach the plastic to the ceiling.During the time the film begins to sag by gravity plastic.
Do this once during the installation.
close up the hole in the film
film is a soft coating, which can be even accidentally make a cut.The situation is certainly not pleasant, but it is necessary to eliminate the disorder and seal the hole in the ceiling.So
- Cut a patch of cloth helmet (usually material left installers, which should not be thrown away);
- painted on her face and gently putting a glue.This should be quite cautious, or wrinkles in the material.Gently smoothes the surface and wait for drying;
- If you just can not put the patch in such a case, some do applique or applied to any pattern on the surface of the film.In this case, the connection is also not visible.
do the right layout, sealing holes in the ceiling and sometimes impossible (sm.Remont suspended ceilings - can you do it yourself).It will take a complete replacement of all the material.Rate
correct your strength and take your time when performing raboty.Otverstie Ceiling do not so difficult.
In this regard the most important orderly performance and correct measurements.In this case it is better to measure seven times indeed.
Take your time and everything will be done well and efficiently.