The ceiling in the bathroom plasterboard do quite practical.It is not clever design, which can be done by hand.
And it does not spend a lot of money.You can hide communication and make perfectly equal plane.
In this article, we'll show you how to do in the bathroom plasterboard.The price of the material is not so high, and such a pleasure can afford any.
All work can be broken down into several components.Just need to make a qualitatively using good stuff.
prefer those brands that has gained its popularity.Avoid new blends that are produced by someone unknown.
Training tools and material
to continuously carry out work should be fully prepared.In order not to be distracted during the conduct of operations.So
- To begin to imagine exactly what you want to see is displayed in the drawing (lines leading plasterboard ceilings - what is needed).This is not just.
Now you will be able to correctly calculate the amount of material that will be required for the conduct of operations;
- Bath, is the room where humidity.Therefore it is recommended to apply water-resistant material.
not worth the risk, when using a conventional, over time he will pick up moisture and crack;
- must now decide on the material for the frame.This is a serious question.
can apply metal profile and can be used wooden beams.The installation of any of these materials is no fundamental difference.
However, there are some details which should look.
Warning;If you choose a wooden frame, then give preference to the beam 50/50 and humidity greater than 12%.Before installing, take it in place and make the antiseptic treatment, which is in the retail trade.
desirable to impregnate the material twice and let it dry thoroughly.You extend the life of the structure and prevent the formation of mold or mildew.
- plasterboard ceiling in the bathroom can be attached to virtually any base surface.Just be sure to look clean and very large bumps.
that may affect the placement of the plane of the assembly.Immediately identified and lighting.What
fixtures you want to apply.On this will depend on the method of installation;
- To conduct work you will need a hydraulic level. that you can buy ready-made or make yourself.
It's not that hard.Take a rubber hose with a diameter of about one cm. Long, one meter more than the diagonal of the room.
After that the pharmacy get a glass tube, which is tightly enter the edge of the hose.Insert them and the level of ready-to-use;
- immediately identify and locate additional insulation for the ceiling.This will determine the height and placement of the plane;
- Bulgarian will take a cutting wheel or tin snips;
- Do not forget about the fasteners, which also must be purchased in advance.This hangers, anchors, dowels, screws.Do not take plugs in sets.
They do not provide a reliable fastening.Purchased separately Dummy and buy them on the screws with a diameter of a few meters.below it a hole element;
- immediately provide space connecting fixtures.To do this, use a junction box, which will make the installation.
Calculate the amount of fixtures, and do not take the lead with a cross section in the butt should provide clearance of strontium increase by 20%;
- before installing drywall sheets are brought into the room where the work will be carried out.Material must dial the desired humidity and temperature conditions used to.
If the sheets are not equal, then put them under pressure.They need to have a perfect form;
- hacksaw and hammer will be needed, and building level, but not less than one meter.Prepare and Nylon thread.
plasterboard with their hands in the bathroom should be mounted on the frame (sm.Karkas ceiling plasterboard - all the little things or little things do not happen.).Which will be the plane for installation.
Therefore, it should be set sufficiently hard and have a perfect plane.If you do not perform, we can be wrong geometric shape of the whole structure.
- First, we should choose the lowest corner of the room. Put a mark at this point and then add the width of the profile or timber, and also set the mark;
- Now it should be transferred to the other walls.To do this we need to apply the hydraulic level.
by which we transfer the correct size.Transmission;
- Now we need to connect all the markers.That we will be placing a ceiling plane.To do this, we apply the nylon thread.
We just repel the desired level.We have a plane installation.
On it we will strengthen the profile.Do not pay much attention to the material, it can simply be bent.
makes the connection is on the line;
- Cropped profile or a bar tender in size.To do this, use grinders with cutting wheel or tin snips;
- Then fasten the profile to the wall. for wooden surfaces is done using self-tapping screws.
for a plane made of concrete, apply a punch.Make a hole and make connections with dowels;
- Now do the layout for the longitudinal profile.It is said that it is necessary for securing the edge and the middle of the sheet.
I will say that it is not for the bathroom.We should not forget that there is high humidity and the material can lead.So do mount profile every 50 cm;
- effect the desired line.Making the cutting of the material.Fasten it to the surface.Apply dowels;
Note: The panel houses can be a cavity in the plate itself and, therefore, they may fail.I am for the fortress compound then pushed into the cavity of the stones.
Some advise to drive a wooden wedge.But he rassohnetsya and does not fulfill its function.
- When installing the frame we have to make a flat base.To do this it is best to apply the line .
When we have attached extreme elements around the perimeter of the room, they should attach a fishing line and pull.Details of the framework that will be in the middle, is put on the line and adjust the plane of the mounting using spacers;
- not do much tight connection elements, soak a small gap on the order of 5 mm.This way you will avoid trouble with the expansion of the material during temperature changes.
Note: During the works, determine where the wires pass.If you do not have the wiring diagram, then determine its location using the determinant.
He is not much to risk.During the conduct of work, disconnect the power supply of the branch.
Do not take chances.
Make wiring for lighting
After proper installation of the frame, we need to separate wires or a single wire for lighting fixtures (luminaires sm.Delaem own bathroom ceiling).So
- Install the junction box;
- note attaching fixtures;
- Making channels for mounting wires;
- Company holds in the corrugation.This we will do the wiring safe;
Warning;Do not use during the connection twists.Use the special terminal block.
that will make the connection quite reliable and provide good contact.
- Fix the wire according to the channel;
- Connecting the lighting and look light distribution.Some do only one lamp in the bathroom.
However, the principle does not change the posting.Especially if you already do, you will not be difficult to do more light near the mirror.
We still only have the opportunity to redesign the lighting.But after installing the sheets it will be quite difficult to do;
- If you are satisfied, then switch off the power and remove the lamps.
Now ceiling in the bathroom plasterboard (see: How do the best for plasterboard ceiling or walls) is necessary to trim the sheets of material that we have already purchased leveled in the stack.
installation is done by the following rules:
- Gypsum ceiling in the bathroom should start to finish from the corner of the room. not attach sheets tightly to the wall, make a gap about 5 mm.
absconding plaster and skirting board;
- screws used to connect the metal, the length depends on the thickness of the sheet.The connection is performed strictly perpendicular to the plane.If
screw went wrong, do not do a fixture in the same place.Stand back and take a couple of centimeters fasteners;
- Before installing the spare element should be the place of installation.View the correct placement.
edges of the sheets must be joined to the profile rather than on weight;
- before installing it is necessary to remove the chamfer on the front of the sheet.It should be of the order of 5 mm.
not attach sheets butt.Make a small gap between them;
- In the process, you will need to cut the material.For this use a flat surface.
best to approach the table.Put a sheet on it.
Using a ruler draw the line with a pencil.Applying a flat rail and make an incision with a sharp knife.
Thereafter, the sheet is shifted from the edge began to be 5-mm.Applies timber line.
pressed down and click on the hanging side.The material breaks easily and strictly on line.
After the break should be made smooth edging.This is done with the help of the planer;
- Now, about the coverage.First, apply the sheet to the mounting base, and marks the spot output of the lamp.
Recording a sheet and make the hole. To do this it is best to apply the crown, which is placed in the drill.
They eat in the free market, the main thing is not to be mistaken with the size.You put it in a drill and make cutting.Do not push strongly to the material.
Do everything smoothly.When pressed strongly, the material can have a snack and pull the pieces.
After the fracture, the line should be treated with a plane;
- plasterboard ceilings in the bathroom, it is desirable to handle with the putty perforated tape.It will make a better connection.After
room is high humidity.This will secure it the joints and extend the life of the assembly.
Here is a complete guide on the device ceiling.There are many types of decoration and a lot of materials that are used.
You can find answers to any questions.Starting from material fabrication and finishing design.
lot on the subject of photos and videos.However, plasterboard ceiling in the bathroom is a good choice.If you do all the work slowly and accurately, the design can serve for a long time.
Just on our website you can learn about how and what to paint the ceiling in the bathroom.