Bunk stretch ceilings allow to quickly close the matter with the old repair the ceiling.This dust and dirt minimized, you can not even make furniture out of the room.
A wide range of colors and textures of the films, the diversity of skeletons and the ability to accommodate a variety of light sources are absolutely not limit your imagination in choosing the design of the ceiling.
With multi-level ceilings can divide space of the room into different zones.Using a combination of glossy and matte surfaces, get a complex play of light.Application
printing on the cover allows you to create the illusion of sky overhead, and the use of special lighting techniques makes it a "starry sky" .Ostaetsya only understand how to do it with their own hands.
First you need to clean the dust from the existing ceiling, peeling plaster or putty and thoroughly primed surface soil deep penetration (preferably in two layers, with intermediate drying).
This way you protect yourself against potential problems in the future, because if a film gets on top of a garbage, there is a need to dismantle it, which is expensive and not always possible.
Now you can start the markup:
- at a comfortable height (for example, 1.7 meters above the floor) with the help of water (laser) levels do mark the corners of the room.
- connect them, get horizontal (base) line around the perimeter.
Council.It is very convenient to use while building a cord with dye powder.The layout must be done together.
- Determine the lowest point of the existing ceiling by measuring its distance from the base line at several points along all the walls and corners.
- from the bottom of delaying the project level, the upper and lower tiers of the ceiling.
- These marks carried out parallel to the baseline two horizontal lines around the perimeter of the room.
- You can now move the base ceiling design with drawing the boundary line between the tiers.
Council.Straight lines draw conveniently, using a range of construction law (or any flat rail of suitable length).
circles painted as follows:
- point in the center of the hole drilled in the concrete and the dowel hammer PVC, which are tightening the screw;
- Prepare a piece of thin wire with two eyelets at the ends;
- One loop put on the screw, and the second insert a pencil and draw a circle (or a portion thereof);
- In order to draw a smooth curve of complex shape on the ceiling of the drawing is transferred from several reference points.According to him put a thin flexible rail or strip of flexible material and lead round a pencil;
- At the points where the lower tier to the wall, connect the line elevations tiers vertical cutting;
- notes on the location of the ceiling lighting equipment.
The next stage will be the installation of all communications that fall into the space behind the ceiling.It may be air ducts, piping and electrical wiring.
It must be done in a corrugated tube, summing up the wires to the sites of the planned location sources sveta.K base ceiling, secure mounting platform for special spotlights, adjust their height to the level of the web.
If you plan to install an overhead chandelier, it is necessary to manufacture and install a platform for further attachment.
To comprehensible procedure for further work is necessary to consider design features:
- Wall profile (baguette)
- plug splitter
- plug wall Profile
- canvas upper tier
- Cloth lower tier
mainload from tensioning frame carries , on which are mounted separator and bump.That is why it must be sufficiently strong and rigid.
There are many methods for manufacturing this item.The main task - to get fixed rigidly vertical bar, follow the contours of the steps of the transition between the tiers.
Frameworks prepared in advance
You can make the frame together with profiles and then fasten the finished design on the ceiling.
In the photo you can see that on a curved base (plywood or OSB) fastened with screws for furniture corners, which are secured with aluminum rivets and otboynik.Podobnye splitter design used mainly firmsinvolved in the sale and installation of suspended ceilings.
This significantly reduces installation time at the site, since the frame is made in advance. advantage of this method it is also a high precision of production if quality measurements.
His hands are not difficult to make such a separator instead karkas.Inogdaangular profile can be used, but rather chipper - structural profile.
In this case, there is a range of finished products a certain radius of curvature (convex and concave).
of various combinations of these preparations can be made quite an interesting framework.
Manufacturing framework "in place»
In this case, to the ceiling attached pieces of wood perpendicular to the stairs quite often (depending on the curvature of the bend), and to them bolted screws strip of flexible sheet material (PVC, thickness of 10 mm orplywood of 4 mm in two layers with offset joints, to get smooth curve).
If the width of the stairs is large, it is necessary to provide for fixing the position of the lower edge of the band (for example, screwing her and bars inclination angle of 45 degrees with cut ends) .Esche one of the ways is to use for the manufacture of the frame under the bunk stops ceilings plasterboard profile.
perpetuate securely mounted band splitter and bump.They may be aluminum or plastic. Plastic profiles can be bent and easily fixed to the curved surfaces.
aluminum - are more reliable, but their price is higher.To create curves using profiles with notches.
If you wish with your own hands, you can frame with backlight.
- Furniture Corner
- band - reflector
- Wall profile or separator
- upper tier
- Ceiling profile
- LED strip
- Wall profile
- lower level
remains secure wall around the perimeter of a baguette horizontally and in places where the stair is suitable to the wall - vertically (if any) .Karkas ready.
It is at this stage fulfill the heat and sound insulation of the ceiling (if provided by the project).
heat and sound insulation
The insulation must be made of noncombustible materials.It is best to use mineral (stone) vatu.Ee fastened to the ceiling with plastic fungi.
Council.It can be used for mounting screws, twisted into a dowel on potolke.Mezhdu them pull a thin wire or a solid thin twine, wool which does not sag.
use as insulation foam and polystyrene foam is undesirable because they burn very well, while stressing the harmful to human health.Come responsibly to the choice of insulation (sm.Teploizolyatsiya ceiling - materials and methods).
If you plan to PVC fabric, vapor barrier, you can not make (the film does not let moisture).Exceptions are bunk acoustic ceilings stretch as used perforated film and the use of a vapor barrier for the protection of insulation required.
How do (sm.Montazh suspended ceilings with their hands - it's you)?
start it from the lower level:
- Specially straighten a cut sheet and temporarily suspended at the corners of the room.
- include heat gun and heat the web.The air in the room do not need to specifically heat - he warms up.
Note: Before starting work, you must remove the items from the room, the heating of which is invalid (flowers, home appliances and so on).
- canvas stretched and uniformly secured in baguette with a pitch of 15 - 30 cm around the perimeter, using a special spatula.
- arisen folds and wrinkles heated further while tucking into the web profile is already completely.
Mounting top level is carried out similarly. gaps between the ceiling and the wall and between the tiers covered with special decorative plate.
can only install spotlights and lyustru.Idealno smooth, modern and reliable two-tier suspended ceiling is ready.