Multilevel suspended ceiling is sometimes simply necessary in the finishing room.There can be many reasons.
If you need to hide the communication on the ceiling, or you do not want to align the reference plane of the ceiling, and then you will be able to help the multi-level ceilings.This article and let you do it yourself.
To begin to see the pictures of these types of structures, then a video installation, and then doing multi-level ceilings with their hands.
Installation multi-level ceilings
This work can be done by hand and without the need for outside help.The truth is to say that you can do it, if you have the concept of the fitting suspension systems.
Otherwise you'll have to consult specialists.It's about a harpoon connection is the most reliable way.
to continuously carry out work we need to prepare the following tools:
- To make holes and we need a hammer drill with pobeditovye soldering;
- To determine the level of finding the plane and perform frame purchase hydraulic level, or you can do it yourself;
- to determine the level of need and building level with a minimum length of one meter.Also prepare and nylon thread, which should not be less than the diagonal spaces;
- screwdriver and expansion;
- also need a gas gun.You can use a hairdryer and construction, but it should be high-power;
- carefully Gaugeable area of the premises and purchase profile.About calculations take into account the waste, which does not turn out to avoid.
Preparation of the reference plane
In this design all the work begins with the preparation of base mounting.On this will depend the whole configuration and durability.
geometry must be perfect, otherwise then you will not be able to fix anything.So
- first step is to remove the plane from the previous coat.To do this, use a brush on metal.Then do visit the surface;
- If the ceiling is a manifestation of the fungus, then it should be removed (sm.Gribok ceiling - the emergence and solutions).To do this, buy retail antiseptics that make processing.
Prefer liquid deep penetration and make the cover a few times.This work is necessary to make sure.
Even if there is no damage, it is still a job worth doing.If there is subsequently an illness, then it is difficult to remove;
- We are not interested particularly uneven, but if there are cracks or peeling plaster, then it, too, is correct.For this fragile material is removed from the ceiling using a chisel and hammer.
After that the plaster surface;
- Now do the primer surface.Make sure the work should be done, it will give additional coverage fortress.
multilevel ceiling tension mounted on the frame, which should be done perfectly.Its quality setting will depend entirely on the whole geometry of the ceiling.
should therefore treat it carefully enough.Before the start of doing the work necessary to take the plan and see the place of conducting wires.
If the plan is not, then why not buy a device for determining the cable.Its price is not so high, it is impossible to prevent damage.So
- First paint the ceiling mounting levels.Select the desired configuration;
- find the lowest corner of the room, and set the mark;
- To this we add the height of the size of the profile.If you want to install additional insulation, then it is necessary to take into account the size.
Warning: If you install a heater you should not do the size butt.Make a gap upwards.The material should be freely attached to the plane.
- We now have the mark of the ceiling mount.Now it should be moved to other walls.
For this we apply the hydraulic level.With his help, this can be done most accurately.
We transfer size of other wall;
- Now we need to connect the mark.To do this, use nylon string and simply repel size.Now we have the correct level of finding the ceiling;
- Now cut profile UD, and fastened it to the perimeter of the room.For wooden surfaces can be used conventional screws.
If the wall is made of concrete or brick, then use the punch.After this is done fixing with dowels.
connections should be tight and withstand the pressure;
Attention: The connection must be carried out strictly.The stretch ceilings has a large horizontal load, which is about 70 kg.
per meter.Do not use plugs from the kit.Buy
separately plastic and screws to him with a diameter smaller than the cross section for a couple of holes mm.Only such a connection is reliable.
- installation of dowels is done in increments thirty centimeters;
- doing the same mounting profile and on the second level.This is done, as described above;
Warning: Do not forget that a second tier should shift into the room by the width of the drywall.This material will have mounted on the vertical plane of the ceiling (step).
- Now we need to do and fix the uprights.Cut them to the desired size and fastened using dowels and punch on the inside of the box.
distance between them should be not less than 20 cm. Slats profile is fixed with screws on metal.
continue doing multi-level ceilings.The video shows that more should be done the wiring for the lights to be purchased in advance.So
- find a place to install the junction box.To it must be easily accessible.
Sometimes you may experience problems and we need to rectify the fault.Also, if you plan to use energy-saving lamps, while the need to install step-down transformer, find a place for him;
- Stamp on the basic points for ceiling mount fixtures;
- from the junction box channels and do them perform fixing wires.
Note: Calculate the correct conductor cross-section of the cable.You can not make back to back.Make an increase in cross-section conductors, this will give you the power margin.
also perform connection using the terminals that will ensure the reliability of the connection.Avoid twists in the manufacture of wiring.
Prefer cable with copper wire, it is more reliable.
- on site lamps do release cable for free fastening and circumcised him;
- Fasten lighting.Connect the power supply and check the correct operation of lamps and light distribution.
Make it mandatory.As long as you can without any problems to fix.
After installing the ceiling it will be impossible to do.If you are satisfied, then disconnect the power supply of the branch;
- If you plan to install insulation, then now is the time to make this work.
Installing ceiling coverings
After correct mounting frame you can start assembling the coating:
- First fasten drywall.There should be considered a single item.Links
material is on your profile and can not be fulfilled shed.Fastening screws do.You will need to cut the material.
This is done using a standard knife, it has a detailed article on our website;
- After mounting plates, cover should be treated with putty.
surface must be perfect.We are making the first start of treatment and after complete drying of the surface finish pass.And gruntuem surface;
Note: If you use the lights in the plasterboard, then you should first make a hole in the material, and only then to carry out surface treatment.
- canvas for suspended ceilings is mounted last.Prior to installation shall be read installation instructions.She
separately for each material.Multilevel suspended ceiling to make the most possible, only during the conduct of the work can not be in a hurry.Cut the baguette
in the right size and fasten it to the inside of the vertical box.The connection is done with a minimum pitch;
- Now warm up the room at least 50 degrees.Start fixing film from the corner of the room.
Before making the connection of the film should be heated to 70 degrees with a heat gun.Only heat is evenly across the plane, not too close to the gun;
- Then, using a spatula is inserted harpoon prints.After clicking it will be understood that the attachment is satisfied;
- Then do the same thing on the opposite corner diagonally.When the same is true for other angles.
now fully dressed with tape and start from the middle of the baguette.Make a dressing around the perimeter;
Note: In places where the cable fixtures should be provided with holes in the film and covered with a plastic ring incision, which is purchased in advance, and only to correctly determine the correct diameter.
- After full cooling of the film, she is stretched and becomes perfectly flat.
Now you know how to make multi-level suspended ceiling after the full tension of the film can be fixed, and baguette, which will finish the ceiling finish.The design can be done on almost any number of levels.
is possible to perform covert illumination, article on the implementation of this work is on our website.The most important thing carefully vymeryat all sizes, you can not go wrong here.
Just on our website you can learn about how to choose the design of ceilings in the apartment.