ceiling of plastic panels in a bathroom, is perhaps the best option finishes.The advantages of this type of ceiling far exceed his own shortcomings.In the first place, it is possible to allocate a relatively inexpensive cost, and of course - practicality.
plastic panels ceiling bathroom will serve you faithfully for years, because they require minimal care, and behave well in high humidity .It is also worth noting the fact that there is no need to carry out any repairs or waterproofing an existing ceiling.
plastic panels - tight and do not absorb moisture, do not be afraid of them that will accumulate water hides all wiring, pipes and ventilation ducts, allowing to make this ceiling are only beautiful, but also to apply for a design decision.Do not deviate from the topic, I will say that such a ceiling can make a multi-level and even combine different colors and directions (see. Suspended ceiling made of plastic panels: advantages, disadvantages and features of instal
mounting ceiling in the bathroom
to make their own ceiling in the bathroom, we need:
- drill or a hammer
- sharp knife
- dowels, screws to press the puck
- Metal profiles for suspendedflow 2.5 cm to 2.5 cm (UD-profile) and 2.5 cm by 6 cm (CD-profile)
- plastic panels for the ceiling bathroom
- Start bar or ceiling moldings
installation of plastic panels of the ceiling is a fairly simple process and does not require special skills of construction.Here we describe the stages of installation technology, and you will see that to do it yourself is not only possible but also quite easy (see. The plastic paneling on the ceiling mounting features)
- bathroom ceiling trim plastic panelsLike any job, had read with training facilities, and marking the future ceiling.It is advisable to remove all the excess out of the room - it can interfere with work.To mark framework necessary to measure the level on the perimeter and draw a line on the wall, where it will begin a new ceiling (cm. Frame of the plasterboard ceiling: design features)
Tip: If you are lying flat on the wall tiles,You can not use level, and to do all the measurements from the tile joints
Tip: better to plan ahead and buy room lighting fixtures in advance.When certain fixtures may need, lowering the ceiling with respect to old - up to 10 centimeters.
- profile UD, cut along the length of the walls, pre-measurement of the desired length with a tape measure, drill holes in it in increments of 50 cm dowel.
- bailiffs profile to the wall to make a mark on, drill holes in the wall, in places of attachment.Securely fix the profile to the wall dowels.
Tip: Fixing "rapid installation" is better suited for the job, they can score a hammer
- Profile CD otezaem for the required length or width of the room.Please note that the plastic ceiling panels bathroom attached perpendicular to the direction of the profile.Then paste it into the guide profile, the distance between the carrier profiles must be at least 40cm.
Tip: The panels may sag if the distance between the profiles is too large.
- If the profile is longer than 1.5 meters, to give structure rigidity, secure it to the ceiling with metal hangers.Profiles also in places of insertion, twist the screws should
- When the frame is ready, you can proceed directly to the mount plastic panels.
Tip: If you do not plan to use as a lighting spotlights and prefer classical chandelier or ceiling lamp, at the point of attachment is necessary to install an additional profile for installation.
- before mounting of the panel must be installed around the perimeter of the starting bar with screws to the guide profile.
Instead Homepage rail can be attached ceiling moldings
Tip: Install guide profile not required, it can be glued in place tothe tile ceiling moldings for liquid nails.
- plastic panels (see. The plastic ceiling in the kitchen with his hands) for a ceiling in the bathroom should be cut to the required size and insert one end into a launching rail and slightly bent, set the other end.Tuck it came down to the wall and tighten the screws with a press washer.
- Subsequent panels are mounted in the same way, clinging to the previous butt.Care should be taken so that the panels entered the same throughout its length.Do not overdo it with the effort of pressing, because the material is quite fragile and can easily break.
- last panel is cut along the length of the knife blade, and fixed by inserting the starting bar.It is not necessary to fasten.
- remains is to remove the traces of our workflow, and the room is ready for use.
- Before you mount the ceiling in the bathroom of plastic panels, take care of the future clarification of the room (see. Ceiling fixtures for the bathroom: types and installation).After installing the frame, pull wiring to all prospective fixtures.The wire is better not to feel sorry and leave "tails" longer, the excess can be cut off forever.Posting desirable double insulated, and be further protected, corrugated plastic hose.Immediately test the results.
- panels reaching to the place where there should be lights, mark and cut a hole the right size
- can immediately install the lamp and fasten the plastic cover in its place
- Pull the wires through the holes and finish the installation of the ceiling
- power to the fixtures using the terminal block, and set the bulbs
Tip: using the plastic panels,may visually change the dimensions of the room, placing them in the right direction.Attach they can even diagonally, what recourse is extremely rare, although it is interesting solution.The ceiling of the bathroom plastic panels - video lessons do not require.Having made such a ceiling with his hands can save money and get a lot of positive from the process, because it's nice to do something for themselves.