Now a great demand for PVC stretch ceilings, which are represented by a large variety of colors and with the different structure of paintings.But PVC fabric across the ceiling area is not as efficient as the installation of stretch ceiling in plasterboard, because, firstly, thus created a multi-level ceiling, and secondly - there is the play of light, color and shadow that it opens a large space fordesign.
so that the combined ceilings are best suited to the same combination of PVC and plasterboard will be cheaper than a solid sheet of vinyl.
combination of drywall ceilings with PVC.What can you do yourself?
frame for plasterboard
- to set ceilings on the drywall, you can independently perform all the work related to the installation, putty and painting drywall .
And above all, you need to make a frame for the ceiling of plasterboard metal profiles, as will the combination of stretch ceiling and drywall.
First of all, you have to set the level of plasterboard for mounting metal frame .It should take into account two values: the first - is the depth or width of a stretch ceiling fastening profile and the second - is the visible depth of gypsum level, in other words - the distance from the lower level to mirror the tension plasterboard ceiling.
Adding these two values, you get a total depth of the ceiling and put in the corner mark on the wall.
- With water levels carry the label into all corners of the room, and in every corner of the place of two labels, ie label against the label on the walls of the conjugate.
- between the two marks and tighten the thread choklayna, pulling her repel control line for a guide on the perimeter of the room.
- Now you need to determine what place and what size you are allotted stretched canvas and draw the outline of the main ceiling, that is, make the design of ceilings.
- Now you need a ceiling on the main draw the outline of the profile tie UD .To do this you need to cut the profile 5 cm at the sides and bend is screwed to the ceiling of the contour line.
also need to fasten to the wall profile UD, in places where there is drywall.
- for future plasterboard ceilings stretch nylon thread .Fix the thread on screws, which, in turn, thread the bottom in the wall profiles UD.
- next step is to combine the plasterboard ceiling with tension profile CD will install in a horizontal plane on hangers.
- Profile CD has to invest in UD profile and reach a virtual bending (bending of the main ceiling already fixed profile UD), being fixed to the U-shaped hangers.Profiles are offset by a thread.
- clipped another UD profile and puts it on the cut ends of the profiles CD .Now you connect the two remains clipped Profile UD (top and bottom) vertically.
- to connect the profiles vertically cut pieces Profile CD and invest it in the top of the profile UD, and the bottom slice side jumper and screwed to the lower plane of UD .Now you need to sheathe a metal frame plasterboard.
- Do not forget to wiring electrical wires for lighting and communication lines and hide the wires in the corrugated cable duct, attach it to the ceiling .
So how do you make a combined ceiling - drywall and tension, the wires have to lead to a stretch ceiling.
Council.For screwing profiles and hangers to the basic ceiling, use plastic anchor flare, so it does not sink into the voids of the concrete slab.
This usually use a dummy plug 6mm diameter and a screw diameter of 4-5 mm.
Installation of drywall sheets
- now proceed to the installation of drywall mounted on a metal frame .Note that the installation of the GCR ceiling requires two or three people, otherwise you will break a leaf when you pick it up and fasten.For mounting
GCR alone requires some experience, so it is better not to risk it.
screws on the metal, 25 mm screwed 30-40 cm from each other, andone sheet of drywall takes approximately 60 screws.
head screw must be recessed into the drywall, so it does not interfere with putty, but at the same time be careful not to break the sheet of paper on the screw head.
- vertical screw the sheets, not undercutting them on the figure.Prune list hacksaw after screw to the frame.
- vertical bar cut the desired size and attach to the frame.If vertically provided sharp bends and do not strip bends, you should cut the paper with the convex side of the bend of the piece of drywall.
Council.For tightening screws in plasterboard, use a special nozzle GCR.
Shade nozzle captures the depth at which the recessed screw, and the paper does not break.
- on the outer corners of the structure, to the drywall should fasten perforated corners for a clear expression of the angle at the filler (see. As a putty plasterboard) (some simply paste filler).
- Prime the drywall and give him a few hours to dry primer.Then you can paint and putty plasterboard of the ceiling.
- himself suspended ceiling should be set for the completion of all work with plasterboard.It is better to invite experts.Incidentally, the plasterboard wall vinyl sheet mounted on the same principle as an additional layer of plasterboard on the ceiling.
Combined suspended ceiling and drywall, combined into a single composition, creating the perfect combination of two materials with different structures.If we add the ability to manipulate the color and shape, the possibilities for design of suspended ceilings made of plasterboard truly open inexhaustible.