decorative moldings - a wonderful decorative material, which masks all errors and irregularities at the "ceiling-wall."It is also called a cornice, baguette, border, or fillet.Most often, the plinth is made of polyurethane foam and polystyrene.
installation of these elements - the final, the last note in your work. you do not know how to fix a ceiling moldings?No problem!Carefully read these instructions and independently repeat each step .
installation instructions ceiling moldings
Step 1. Select ceiling moldings
When choosing a cornice guided by the dimensions of the room.The rule is simple: the wider the room and above the ceiling, the larger must be the baseboard (see. How gash ceiling moldings properly and well - description of the process).But you can change to your standards and taste and choose the view you like decorative element.
should be borne in mind that in a large room with a high ceiling using a small plinth may not appear beautif
approximate proportion to the table
height ceiling moldings and room sizes
to 15 square meters.m.
15-23 square meters.m.
of 23 square meters.m.
example.For a room height of 2.7 m and an area of 20 square meters.m. The recommended height of the plinth 9-14 cm. It can take the value of 12 cm.
Step 2. Calculation of materials
Calculate how much you need to buy fillets.To this end, the perimeter of your room in meters divide by the length of one strip (standard 2 m), and round to the nearest whole number pair (see. The junction of wall and ceiling: how to choose the right ceiling moldings).Fixing ceiling plinths - it is a simple job, but because of the possibility of marriage at the wrong cutting or breakage of the element, take an extra ledge, the more it is inexpensive.
Step 3. Marking the ceiling
Examine the ceiling for irregularities and identify the location of the strips.If the curvature large enough, it is better in these places do not glue the long plinth. They can break.Try not to combine elements of different lengths, in fact much more pleasant to look middle-joint splines than short and long .
Tip!All the marks on the wall, apply so that after mounting ceiling moldings, they hid him.
Step 4. Prepare tools and materials
- Stationery knife or hacksaw.
- assembly handgun.
- Mitre - cutting tool materials at different angles.
- rubber spatula.
- tank filler.
- decorative moldings.
- fastening strap ceiling moldings (if necessary).
- mounting glue.
- latex paint.
- Corner mounting plinth.
- acrylic sealant gun assembly (removal of gaps).
Step 5. Cutting skirting
Before you attach the ceiling moldings, you need to carefully and accurately to make cutting corners straps so that they perfectly straight to dock at the corners. Here you handy miter box.It is important to observe some simple rules.The main principle - first cut the end of the corner .And only then produce trim length.
Please note that the bulk of all baseboards asymmetrical, that is, one side is longer than the other.Long section mounted on the wall, and the short - to the ceiling (see. How to cut the ceiling moldings: step by step guide on the real masters of their craft).If your room straight corners, the problems with attaching the plinth ceiling will not.Just insert a quirk in the miter box and cut it with a sharp knife at an angle of 45 degrees.
Tip!At the bottom of the miter box should be the side that will be attached to the ceiling.Fillet during trimming to keep straight.If the hand tremble, the joint is a gap that is difficult to close up.
Cut the plinth.Cut the front of the case is pasted over the inner corner.The rear portion of the fillet cut, if the angle of the external.What if the angles are not straight?Put the miter box to the side, you do not need it.
Cnachala first attach the baseboard to the wall on one side of the angle. Draw pencil line along the sides up to the corner.We received two direct .Take the second plinth, and attach to the adjacent wall.Using a pencil, two straight lines along the sides.
Plot the intersection of the upper and lower straight lines. Again attach turns plinths into place.Noted on the wall point of intersection of straight lines is now put themselves on the baseboards .You get two tags on every baseboard, through which you need to make a clean cut.
You can pick up at the store special corner mount ceiling moldings, which are inserted into the edges of the elements without the need for accurate cutting.
If you are new in this business - practice on extra pieces.To avoid possible errors in the work, you first need to add on the fillet on the outer corners.But a few millimeters place "in reserve".Then you can podshlifovat excess skin.With internal corners, proceed as follows .The gap in the internal junction of acrylic sealant putty better and tint.
Step 6 Installation of ceiling moldings
There are three main options for how to fix ceiling moldings :
- pasting at the wallpaper;
- sticking to the wall;
- mechanical fastening.
All methods have their advantages, but easier for beginners to choose the first option.Bonding on the wall, perhaps the best way. Firstly, you do not need to re-install on ceiling moldings, if you want to change the wallpaper .Secondly, easier to close up the gaps before pasting.The final result is much more qualitative, because the baseboard and the wall looks like a single unit.
third method is used in the decoration of the ceiling panels and provides the installation of special clamping plate, which is mounted on a plastic plinth .
Now consider the order of the first two methods, the most common .
- Align the ceiling and walls, prime with them.
- Apply glue to the inner corners of the plinth.Try to do it in a way that excess glue is not made out.
Tip!The store offers a wide range of adhesives for ceiling moldings.One of the best is alcohol polymer.It is waterproof, dries quickly and forms a strong bond to the substrate.
- Now attach the fillet to the right place, remove it and leave it alone for a couple of minutes for the adhesive to "grab".Lightly pressing, glue ceiling moldings at the same place.
CautionWith strong pressure on the plinth, it can break or on its surface formed dents.
- Subsequent attach skirting to the wall, ceiling and to the junction of the previous bar.When he reached the corner of the wall, measure the distance to it, and cut the plinth of this size using the miter box.
- After fixing baseboards around the perimeter of the room, zashpaklyuyte all the cracks, gaps and joints.
- If necessary, carefully paint the baseboard.
Now let's look at how to fix the ceiling moldings using mechanical fasteners :
- install corner elements;
- lock screws on the mounting plate for the plinth with a pitch of 30-50 cm;
- snap on a plinth fixed design details.
Cropping angles in a plastic baseboard is the same as you would with other materials.
In conclusion, the article
Now you know how to properly mount and ceiling moldings can safely undertake this simple but important work, which primarily requires accuracy.