Today there are many options for finishing the ceiling.The choice of finishing materials depends only on the taste of the owner and the amount of funds allocated for repair.If you plan to finish a budget option, then gluing ceiling tile it is the best choice.First, the material is inexpensive, in the second, it is possible to carry out the installation yourself, thus saving on the payment of services builders.
Ceiling tiles made of polystyrene - is a wonderful option finishing the ceiling.Today's manufacturers offer a wide variety of tiles - with embossed pattern and a smooth, white or tinted, ordinary or special, allows you to create seamless coverage.An important advantage of the coating material is its easy installation.Consider how to stick the ceiling tile, without the services of professional builders.
choice of materials and training tools
When purchasing materials is important to pay attention not only to the appearance of the tiles, but also on its
buy quality stuff
Here are the signs of a good ceiling tiles:
- Each tile has a precise dimensions and smooth angles .If the corners dented or rounded, then achieve a normal interfacing would not be possible.
- If you examine the side edges of the tiles, then there should not be seen signs of fraying .Quality tile has a small, equal-sized grains of expanded polystyrene.
- If the tile is a relief, it should be smooth and clear the entire area .
addition to tile need to buy another and tile adhesive, it is best to choose one that is designed specifically to polystyrene plates.
Calculating the number of tiles
At the initial stage of solving the problem is to stick to the ceiling tiles, must decide on the amount of material.Make it easy enough.
- measure the length and width of the room.
- values obtained are multiplied to obtain the area of the ceiling.
- look at the original packaging with the tiles on which it is intended coverage area.
- Divide the square area of the ceiling tiles contained in one package, we obtain the required number of packages that need to be purchased.
Tip!Since the solution of the problem as to stick the tiles on the ceiling, it is unlikely to do without the need for cutting tiles, therefore it is necessary to increase the calculated value by 10%.
work is carried out should be prepared:
- Comfortable ladder.
- meter line.
- knife or office building to break off blades.
Consider how to stick the tiles on the ceiling, breaking the work into several stages.
Before stick ceiling tiles should be carried out surface preparation.
- If the ceiling is the old coating - it must be removed.
Tip!If the ceiling, and was previously decorated with the same decorative material, the question may arise as to pull out the ceiling tile?I must say that the process of removing the old tiles simple, but quite time consuming, to remove the old paint should be, hooking tile trowel and clearing the remaining glue on the ceiling.
- Next, inspect liberated from the surface of the coating in order to identify defects.If ceilings have cracks, dents and other irregularities, they should be putty.
- leveled surface is treated with a suitable primer for the material overlaps.This operation will provide better adhesion of glue to the ceiling slab.
Tip!It is particularly important primed wooden floors or ceilings sheathed with plywood.Otherwise, the tiles will stay a lot worse.
Before putting the ceiling tile should mark up the ceiling.
first determine the method of arrangement of tiles, they can be stacked as parallel to the wall (direct method), and diagonal (see. How best to glue the ceiling tiles on the diagonal: video).Start laying, usually either from the center of the room, or the location of the chandelier.
markup required to perform the splits.
- end of the twine is secured with tape at the far corner of the room.
- other end of the cord reinforced at the opposite end of the room.
- Similarly, the second fixed segment of twine as a result the room is divided diagonally.In this case, the intersection of cords should form a right angle.
- pencil along the fixed cords be marked on the place of intersection of the lines will be the first place stickers tiles.
Tip!Most often, the chandelier is not exactly in the center of the room, so the markup is necessary to make a little differently.To this end, through the attachment point chandeliers spend two lines parallel to the wall and perpendicular to each other.In these lines formed right angles bisector construct (ie, divide them in half) and draw these lines to the intersection with the walls.So we got a markup on which the label will be the ceiling tiles.
consider how to stick the tiles on the executed layout.Work carried out so:
- On the back of the tile adhesive dots applied.
Tip!The adhesive composition should be applied along the perimeter of the tile and at the center thereof.
- first tile is placed at the intersection of grid lines so that its edges are exactly coincided with marked lines.
- further from the first tile begin forming two perpendicular series, combining the edge tiles with lines marking.
- next rows of tiles are glued, from the first, when the work should follow the registration directions.
- at the wall-ceiling joints often have to cut the tiles to stick, because the size of rooms is not always a multiple of the size of the tiles.
consider how to lay tile, diagonal method is selected labels.
markup in this method is carried out similarly, but the placement of the first tile will be different.In this case, when installing tiles with lines marking need not combine edges, corners .Of course, this sticker ceiling tile is a more complex one and requires a certain skill.
- on the tiles allow you to create seamless coating on the back side made special markings arrow triangular shape.These indicate the orientation of the rings relative to each other.In this case, the label on the ceiling tiles should be made so that all the arrows are in the same direction.
- Most sticker on the ceiling tile is made of where the chandeliers.In order to lay the tiles in fasteners, we have to cut corners in the four adjacent tiles.As a consequence of the cut will be covered with a cap chandeliers.
- before applying the adhesive on the tiles, you should read the instructions for it.The fact that some adhesives require soaking after application, this requirement can not be neglected.
- final touch when installing ceiling tiles - gluing skirting around the room (see. Ceiling PVC moldings: Features installation) and installation of outlets for lamps.Then trim the ceiling is completely finished.
So, ceiling tiles made of polystyrene - a practical option finishing the ceiling, which is quite easy to perform with his own hands.See how to put the tiles on the ceiling, can be subject to construction sites, there are diagrams and location of the panels give advice on the implementation of works.