plastic ceiling is the perfect solution for decoration purpose subsidiary, as well as bathrooms in homes.It can be used with equal success to arrange a balcony, bathroom, garage or gazebo.This polymeric finishing materials are not afraid of moisture or frost, and are able to maintain their original appearance neat for many years.
How to make a plastic ceiling in any of the rooms, our article will tell.
choice of material for the plastic ceiling
before doing a ceiling made of plastic, it is necessary to choose the right finishing material.
often stop the choice on one of the following options:
- plastic panels .Used usually in the range of premises.Due to the abundance of different colors, easy to pick up plastic panels to the existing interior of the home.Besides, they differ considerable width (about 30 cm), which reduces the ceiling surface of the casing.
- plastic siding ceiling .More than the usual plastic material for the creation of ceilings, usually white.It is cheaper in comparison with the panels, but the colors lining is quite limited, which leads to its use, with emphasis on practical component.In addition, the width of the lining rarely exceeds 10 cm, so it is a little more time-consuming installation.
Also in this case, the pressing question of how to knock out the plastic ceiling with the least amount of unusable scrap to finish.For example, standard length and panels, and is considered to be lining 3m, but the dimensional range is wider (from 1.5m to 5m).
length of the material should be selected such that it is equal to the length or width of the room, or slightly exceed it.Furthermore, it is rational to select a material of more than one of the aforementioned dimensions of the room 2 times.In this case, the material can be cut in half and with similar success sheathe the ceiling of the room.
Mounting plastic ceiling
Before putting plastic on the ceiling, the need to prepare an additional list of resources for installation:
- carrier material for the suspended structure - aluminum profile or a wooden beam.The first embodiment is more preferable in terms of reliability and resistance to moisture, although more expensive in cost.Him we shall consider in describing the technology of the plastic ceiling.
- set different types of fasteners - dowels, screws, hangers, etc.
- Decorative corner of the ceiling.
Preparation outboard bearing design
So we close getting to the question of how to make a plastic ceiling.
Instructions for its creation involves a preliminary construction of the support system:
- construct erected on the cleaned from the previous trim and lined ceiling.If the ceiling has been lined with plastic, it needs to deal with how to disassemble the plastic ceiling.
- the ceiling to the walls coated horizontal markings indicating the future level of the plastic ceiling.If the device is supposed to downlights in the ceiling, the distance from the base (the ceiling) to the plastic ceiling choose 5-15 cm.
- Further along the horizontal markings are fixed guide profile using the dowels and screws.Step installation fasteners - 20-30 cm. The marking and guiding profile will solve the problem of how to put plastic on the ceiling level.
- On the basis of the ceiling also perform counting in parallel lines along which will later be installed trims the main profile of the support system.The direction of the lines must be perpendicular to the selected direction of installation of plastic elements.Step markup selected within 40-60 cm. With a large area of the ceiling framework may be cross, that is designed as a batten.
- along the lines marking an overlap mounted metal hangers in increments of 60 cm, also using dowels with screws.
- primary aluminum profile mounting for suspended ceiling is carried out by inserting the ends into the guide profile and is attached to the suspension along the lines of markup.During installation, pay attention to the design of the plane was formed strictly perpendicular.
Major work on the organization of recessed lighting should be made after the construction of the frame structure.
Sheathing supporting framework
Now directly, look at how to make a ceiling made of plastic:
- Plastic material customized in size.This cuts the strict central axes perpendicular panels.On the start
- wall under the guide profile (with a minimum gap) mounted decorative area.
- The spike is inserted into the gap provided by the first plastic element, the rear wall of its groove with screws attached to each adjacent strip profile.
- Spike next element is embedded in the first groove and secured to the support system in the same way.So perform all lining the ceiling.
- last bar trimmed in width and fixed to the ceiling as a decorative bracket.
How to make the ceiling smooth plastic?
approach with increased attention to the positioning of the first plastic element, as it will depend on the degree of flatness of the installation of all subsequent plastic.
In this article, we figured out how to make a plastic ceiling in different rooms, provided recommendations for choosing the most suitable for this material.For those who wish to see firsthand instruction on how to make the plastic ceiling - video tutorial thematic content will be able to provide answers to all your questions.