In modern building in front of the performers and designers often specify a task that requires organization specific acoustics of the room, giving the ceiling aesthetic appearance and placement of technical networks in the hidden cavities.It is necessary that all the work was done in the shortest time and at minimal cost.Therefore suspended ceiling is the most optimal solution in this situation.
This design not only gives installers the necessary space for networking and communications, but allows you to give a room a beautiful appearance, which then can be changed and supplemented during operation, without resorting to drastic measures.
whole process of work can be divided into several stages.Thus, each of them can be performed in several ways and with different building materials.This guide is considered the most simple device ceiling, which is produced according to generally accepted standards.For example, consider the most common ceiling Armstrong.
- First of all, you must determine the number of constituent elements .To do this on a piece of paper draw a scale ceiling, which is divided into cells of 60 cm. In this case, they must be positioned so that it turned out as little as possible of small scraps.If this is impossible, they are disposed on the far side of the room.
- Then fold all sides to give the length of the perimeter .On it must be ordered perimeter area.
- Folding length longitudinal sections within the perimeter, get yardage carrier profiles , and the number of remaining lines bought cross section for suspended ceiling.
- Suspensions must be purchased at the rate of one piece per meter bracket profile .
- number of panels to be taken by the number of the resulting cells .
- After making payments ceiling sanded and treated with antibacterial primer .
This amount of material and technology of mounting ceiling recognized as the best and reliable.It is used around the world for rooms of any size and destination.
for product calculation is not necessary to use various calculators, which are laid out on the Internet.
They have a greater error.
- In the beginning, it is necessary to make the skip perimeter walls to the level of the intended placement of the ceiling.You can use lasers or water level.Also for convenience, use the thread with blueprints.
- As a result, you should get a smooth line on all the walls of the room.As it should be done and installation bracket.This is done using percussion dowels.
For precise marking, you can use the laser pointer, which is mounted on foam, placed in a container with water.
the bracket and the transverse profile
- Mount profile in accordance with a pre-made drawing, which was used in the calculations work.
- For this special is attached to the ceiling suspension, adjusting it to the required distance.
- clings to him bearing profile, the ends of which are located on the corner of the perimeter or combined with other materials of the same type.
- Once installed a second carrier profile, it connected to the first by means of cross members.In this suspended ceiling mount technology involves the use of special locks, hooks which are located at the ends of the profile, and the grooves are at a short distance from each other over the entire length.
should be applied when installing the water level to avoid sagging ceiling.
Additional works and installation of equipment
Once the frame is fully assembled, you can begin wiring communications and utilities.All cables feature walls, and only the lighting system of the room are displayed directly to the installation of devices.For ease of installation for you to take multiple cross-sections, which will then be in place.
Modern technology provides for the manufacture of false ceilings located in the sections special fixtures for false ceilings.They are mounted in the same way as the decorative panel, which is then connected to the mains.
Installation of decorative panels made by their installation in the resulting cell.At the same time they are held there only under its own weight, without additional fastening.Therefore, if necessary, they can be raised to form a hole for access to networks and communications.
There are lots of different decorative panels with different views of the images and drawings.Instead, you can use pieces of drywall to the ceiling, carved in the size or color plastic.This technology allows the ceilings combine different types of materials for the original pattern or organization of a special illumination.
This enables designers and builders of large field for creativity and allows us to implement the most challenging projects and technological solutions.
To trim panel size is best to use a knife and a metal mounting area, and for the profile of special scissors.
Installation of suspended ceilings require precise calculations and accuracy in the work papers.It is very important to follow the correct location of the parts in accordance with the horizontal, which is achieved using the water level.This is a fairly laborious and time-consuming work, which is complicated by the fact that it is performed at a height, causing constant tiredness in his hands.
However, this does not require the installation of artist availability of higher education and specialized skills.With enough patience and the right approach can produce assembling everyone, but a detailed compliance instructions.