Stucco and wall plaster dry construction at this time is the leader in leveling plane on the premises.This is natural, since the benefits of the "dry" repairs are obvious to all, and given the speed and finishing FCL, everything becomes clear.
Now we pass a theoretical course and watch the video - how to make plasterboard one level, taking into account all the nuances of such a finish.
gypsum boards allows you to level any plane in the living room (except the floor) where there is no particular load.Also from GCR can make arches, niches and shelves multi-level ceilings the most bizarre.To understand how to make multi-tiered structure, it is necessary to understand the same level, that is the basics, so we'll look at how to make plasterboard - videos and photos are attached to this page.
- To make plasterboard, you need to calculate the height, because it suspended the construction and it will take a certain distance that you can not always afford the apartment.
It is desirable that the height of the room after the installation of the suspended structure remained at least 240 cm.
- To determine the height of the frame to the ceiling drywall, you need to find on the main ceiling of the lowest point, and, departing from her 25 mm mark the level of the lath (25 mm - ThicknessProfile CD).So, find a point and departing from it at the right distance, make a mark on the wall and carry its water level to all corners of the room.Control line is choklaynom (masking cord), and if the room is small, it is possible to manage a long level or building regulations.
- to main ceiling will be fixed profiles CD, and to ease the installation, control lines can be done there.
distance between the guides should be 50 cm, respectively, reference points are also needed at the same pitch.
Council.To install the first GCR no problem to choose the angle closest to 90⁰.All profiles with respect to the sheet for the correct installation should go at the same angle, so everything should be considered even when the markup, and if necessary cut the drywall.
- Mounting frame begins with UD profile settings on the perimeter of the room where the control line repulsed .Udeshka mounted on anchors with a diameter of 6 mm, and the length will depend on the walls - the worse the long dowel with a screw.If a profile is no hole for mounting, then make them 40-45 cm.
- Now it's time to install tape galvanized U-shaped hangers on the main ceiling.If you there is a guide line - well, fasten the console, focusing on them in 50-60 cm from each other.
- I would like to note that concrete floors are empty, so need a plug with a hat (not to fall through), or push him through the suspension so that the region remained outside.
to the ceiling, use thicker screws so that they are well bulged plug, so if the diameter of the sleeve 6 mm screw is needed, the thickness of 4-5 mm.
- We continue to consider how to make plasterboard - video, photo and text materials.Go to the installation CD.Profile length should be 5 mm smaller than the distance between the walls, it will serve for easy installation and eliminates deformation (bending and twisting).
- Set all CD, without fixing them to the hangers.Now you need to create a flat surface, and this can be a crate pull the nylon thread.To slack profiles are not delayed nylon - at each turn in the center console ears to lift a little higher level.
- When the thread taut and it does not apply to any one of the CD, start leveling the plane.Each profile screw until only one suspension - screw the rest of the console later - now the main level the crate.
- profile with suspension are connected by means of special small screws.If tightening the screws one by one on each side, you notice the play (check by shaking a sharp profile), then add another one.
Otherwise, after installation of the FCL, ceiling impact will "rattle".Fasten together a CD with UD, ears consoles bend sideways.
- considering how to make plasterboard ceilings - video and text explanations note that the installation of sheets produced together, for convenience and safety.Ceiling GCR is 2500 × 12oomm the perimeter and if grab it with one hand, the sheet break.
To make installation alone come up with different devices in the form of flat horizontal struts, but it's good for a permanent job.
- Be careful to ensure that the installation of drywall edge with the long side of the sheet overlaps only half the profile of CD, since the other half will be attached next.On one
GCR need to spend about 60 metal screws, length 25 mm.
- Cap screw must be recessed from the plane of the GCR and that it does not break the paper - using a special nozzle.Its lamp shade, resting on the plane of the sheet, controls the depth of immersion of the head of the screw.
- sealing of joints on the ceiling or make fugenfyullerom or apply self-adhesive perforated tape and shpaklyuyut its usual mixture.After this ceiling is primed and ready for further finishing.
recommendation.For mounting and wiring ceiling light using a double insulated wire type PVA, or hide it in a corrugated cable channel, fixing to the main ceiling.
otherwise sharp edge profiles can damage the insulation, and the frame will be energized.
Council.At high ceiling mount GCR staggered to knock a full line of suture, which is a weak point.To do this, start with a series of whole leaf, and the other - with the halves.
Video - how to make plasterboard, as applied here, clearly show you the whole process works.But remember that every artist can bring something new, even in such a simple job and everyone has their own way of installation.Perhaps something of their own, and you will discover for yourself.