- where to start
- Speaking of glue
- return to laying
- Now you can stack the second row
silicate blocks - a convenient anduniversal material for building a house.They can be used not only for the construction of load-bearing structures, but also for the construction of interior partitions.Building a house takes place in a short time, since the material is light, and put it also is not as difficult as it might seem at first glance.But still need to abide by the rules in the construction of the house to get a strong.
consider all the nuances on.
Tools for masonry silicate blocks
For the construction needs to be a set of tools:
- drill and whisk attachment for mixing glue;
- adhesive for silicate blocks;
- trowel or spatula tile;
gas silicate masonry on the level
- cord or rope-prichalku level;
- normal level;
- saw for cutting the material;
- sand and cement.
Before putting gas silicate blocks, you need to put the waterproofing layer.Normally used roofing material.Laying roofing material produced in the raft foundation, if the foundation under the house is built columnar or the leveled surface of the foundation.Roofing felt fixed to a solution which is prepared either by hand or in special equipment, ratio 1: 3.
Some prefer this solution and put the blocks, but do not do it - very uncomfortable.Can get small stones or large enough, will always have the material removed from the scene, remove the interfering particles, again set the blocks, a waste of time.Special glue - what you need to work.
When waterproofing layer is laid, it is necessary to put it on top of a small layer solution and allow to dry, you can now start building.
where to start
rules laying silicate blocks
Naturally the corners.At each corner of the guides, these may be conventional rebars, perfectly aligned, mounted vertically on the level.Either metal angles established as vertically.Connect each guide cord-prichalku at the height of the first row of blocks, and you can start substantive work, ie installation.
Then glue is applied evenly to the surface of the waterproofing layer is laid on him the first unit.Strongly press the blocks to each other will help hammer mallet.
Speaking of glue
Breeding adhesive can anyone.Take a broad capacity, for example, a bucket from the water-based paint.It pour water (less than half the capacity) and pour a little glue, gradually mix with a drill.Pour and mix the glue needed so that the result had been part of a similar consistency to sour, it is suitable for installation.
return to laying
Forming an angle with one side of the house, you need to go to the other corner and do all operations with them as with the rest of the corners.Next set of blocks begin to lay the first row completely.Be sure to follow the vertical and horizontal installation.Glue is applied to the ends of the blocks and on the surface of the base.
first row is laid out, examine it.Each element should be so that no corner was not put out and did not break the plane of the structure.If there is a defect stacking, it can be skived grater, and thus make the surface smooth.Now we need to make a layout of internal walls, that is needed from the side blocks to pull the rope level.Since the first series for internal partition walls are made perfectly smooth, like the outdoor first row.Stacking is no different: Apply glue to the foundation, to the ends of the blocks, the elements are connected.
Now you can stack the second row
first series silicate masonry
begin construction once the corners.The installation should be carried out in the Extension, if it's not the blocks and bricks.Let's look at the blocks installed on the corner if the first row of blocks stacked on the right, now start laying the contrary left.So We perform every angle, as a result will ensure that the entire structure will be laid Extension.
Alignment series silicate blocks
So gradually laid out row by row, and not forgetting of course, about the interior walls, conducting them together with exterior walls, watching the vertical and horizontal installation.
Ease of construction of silicate blocks in the fact that most of the openings can be cut after complete construction of walls, it can be done with an electric jigsaw.Do not forget just laid in the places where there is an opening, a metal bridge.
example of a house built of silicate blocks: