- Types wickets
- All that is needed for the manufacture of wooden gate
- Production and installation of wooden gate
- All that is needed for the manufacture of metal gates
- Construction materials and tools
plan to make the gate with their hands, you can not ignore existing fences and gates.Depending on what kind of building materials have been used for their construction, and the material must be chosen for the gate.
main types of gates are:
- wooden gate,
- gate of corrugated board,
- metal gate.
All that is needed for the manufacture of wooden gate
most familiar one is a wooden gate.The hands that make pretty simple.Its cost is low, even with the use of boards of high quality.If you buy a less expensive board conifers, the gate will be even cheaper.
for wooden gates need:
- 10-11 boards size 200h14h2 cm;
- two boards size 200h15h5 cm;
- door handle and latch, sheds wickets;
- connection material - about 40 screws;
- antiseptic for wood;
- primer for wood and varnish;
- cement, sand and water for the production of concrete solution.
Of the tools needed:
- plane, chisel, hammer, hand drill;
- screwdriver, drill, pencil, tape measure, level, and building material for shkureniya (numbers 25-16 for the first phase, and 10-9 for the final phase of treatment).
Production and installation of wooden gate
initially need to set the supporting pillars.They digged a distance slightly greater than the width of the planned gate.The standard width of the gate is 1 m, and height should be at the height of the entire fence.
Scheme wooden gate
to the prepared and installed asbestos cement pole with screws necessary to attach the gate sidewall - wooden beams with a height fence.
instructions on making wooden gate
After preparing the supporting pillars and the sides can begin to manufacture the most wickets.First, the board is necessary to process antiseptic.It will prevent the wood from the effects of temperature changes and precipitation, to prevent the rapid decay or damage the tree.Then laid out on a flat surface of the board in the form of the gate, in compliance with the desired width and height.Across these two stuffed crossbar - top, departing from the edge of not less than 20-30 cm, and the bottom at the same distance.For greater rigidity, and hence the strength, you must also fill jib - part timber-framed small size, placing it on a diagonal blade gate - from the beginning one of the crossbar to the other end.
To wicket worked, that is opened and closed, it is necessary to attach the loop to the gate on the sidewall, and the gate itself.Metal hinges corrode, so it is necessary to lubricate them with grease from the inside, and on top - a bituminous varnish.For a longer service gate is necessary to repeat this operation every year or two.
After mounting of the hinges on the gate leaf and mates on the sidewall, it is necessary to put the gate in the loop and attach the latch and handle with screws.
All that is needed for the manufacture of metal gates
The metal gate on its own can be made of corrugated or sheet metal.
Ironwork do yourself without any experience or special equipment is almost impossible.
Construction materials and tools
frame for the metal gate
arrangement for the gate of the trapezoidal sheet needed:
- metal profile frame for creating the gate, the gate sheds, fasteners;
- shaped sheet with a minimum thickness of 1.5 mm;
- asbestos or metal pipe with a diameter of 10 cm;
- means of protecting metal from corrosion - waterproof enamel paint;
- primer for metal;
- welder with electrodes with a diameter of 1.6 to 5 mm;pencil, tape measure and level;
- Bulgarian metal, shovel and hand auger.
As in the case of a wooden gate, set the supporting pillars.As the gate leaf can be used steel sheet desired width.Initially, preparing the framework - it is connected by a welding machine - on the perimeter of the profiled sheet.During welding the metal base under the gate is necessary to provide a place to put the mortise lock.
gate of corrugated
From top left corner of the frame to the bottom right to attach the struts of the same metal profile, from which made the frame.
scheme of installation of corrugated gate
final step when installing the gate will be its priming and painting.
For example, look at the video for the manufacture of metal gates:
With decorative elements
gate aluminumProfile with filling Rolled profile
gate of metal and wood
Wood with unusual design
gate with a lock in the metal frame