- Building greenhouses PVC
- Greenhouse made entirely of PVC
- Teplice polivalki
Having a greenhouse is not only pleasant but also beneficialas yet expensive vegetables in the supermarket, they can already have at his desk with his own plot to grow in warm.Craftsmen invented many ways to the construction of greenhouses of all kinds of materials, but now, with the advent of new technologies is unlikely anyone would do such a structure from used window frames, because you can quickly, cheaply and troublesome to make another, more robust design.In this article we will discuss how to make a greenhouse out of PVC pipe, as well as how to make a convenient watering.
Building greenhouses PVC
of composite materials
to build greenhouses need the following materials:
- five-meter board 2 × 6 cm - 4 pcs.
- four-meter board 2 × 6 cm - 2 pcs.
- four-meter board 2 × 4 cm - 14 pcs.
- six-meter PVC pipe Ø13 mm - 19 pcs.
- three-meter valves Ø10 mm - 9 pcs.
- Durable film 6 × 15,3 m.
- wooden lath - 61 m.
- plastic ties.
- Door hinges and handles.
- screws (if the design is not folding, we can nail).
- metal compound (you can use the ones that are purchased for use with plasterboard).
Before starting work, all the wooden parts treat with antiseptic, then on a prepared site, set the rectangular frame of the boards, not allowing her straight.This can be checked by pulling the thread diagonally, and then attach the frame by driving in the corners of pieces of rebar.On the long side make the markup to set the tube are separated by a distance of about 50 cm. Cut in half and the reinforcement of its type in the marks on the 30 cm into the ground.In order to constantly check how the rod is not entered in the ground, make a mark on it, and hammer until it is flush with the ground.Since the armature is light and flexible, then its score, especially in the hard-packed soil, can be problematic.If this happens in your case, use a pipe as a liner by placing the clog valves.As a result, you should have a "stockade".Each rod should be put on plastic pipes, the length of which depends on the size of your greenhouse, and secure them with special brackets.
Greenhouse from PVC pipes and plastic film
To the rear of the greenhouse frame, attach the boards, which will be attached to the film.In front of the door set.Now the greenhouse is ready.
The greenhouse made entirely of PVC
General view of frame
This design is more complex, but it is stronger and more reliable than the one described above, because it turns a strong skeleton.To work need a special solder for soldering pipes.If this is not available, then this device is very common, it is possible to take the time with friends or relatives.
Since this pipe connection does not provide for disassembly, it is important for you to be a certain sequence.So, you have to figure out how to make a greenhouse out of PVC pipes by soldering.Consider a phased build order, following which it will be possible to perform the work without alterations.
- Solder to the two long pipes, which are the basis, tees with an interval of 50 cm, at the ends of these tubes tighten the cross;
- In the place where the door will be installed, solder two tee that will be required for fastening pipes, performing the role of the door frame;
- Now you can solder the entire framework from which to form an arch;
- Attach the resulting arch soldered 2 lateral pipe of the same length;
- Measure resulting doorway and solder from the door slightly smaller pipe to avoid being a wedge in this slightly movable structure.
door assembly of pipes
're obtyanut the skeleton of the film and a greenhouse ready.
If the winter you do not clean up the greenhouse, then take care of the internal props to a mass of snow pipes are not broken.
shelves, too, can be made of PVC pipes
Another feature of the greenhouses, and welded PVC pipe is the ability to use the same pipe for irrigation, and it needs not so much.For this modification, set in a convenient location in the frame structure valve through which water will get inside the piping.Then, determine which sites you will need watering, thin drill (can be a little nail holding it in a chuck drill), drill a hole in the pipe.Turn on the water and see where spurts and whether it is sufficient pressure.
If you do not have a well with a pump, and the total water supply, note also the factor that in the summer, when everyone watered their gardens, the water pressure may not be sufficient.So check the irrigation system under the most extreme conditions, and only then see whether you want to ream the holes, making them larger diameter.
Ready greenhouse can be seen here: